Sloan 110 Sloan Exposed Flushometer - Manual

Code No. 0816558 — Rev. 3 (02/15)
INSTALLATION INSTRUCTIONS FOR EXPOSED SLOAN
WATER CLOSET AND URINAL FLUSHOMETERS
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship for a
period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company
will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive
remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends
only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL
DAMAGES OF ANY MEASURE WHATSOEVER.
Before you install the Sloan Flushometer, be sure the items listed below are
installed. Also, refer to the rough-in diagram below.
• Closet fixture
• Drain line
• Water supply line
IMPORTANT:
• ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE
WITH APPLICABLE CODES AND REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN
ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
The Sloan Flushometer is designed to operate with 15 to 80 psi (103 to 552
kPa) of water pressure. THE MINIMUM PRESSURE REQUIRED
TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE
SELECTED. Consult fixture manufacturer for minimum pressure
requirements. Most High Efficiency water closets require a minimum flowing
pressure of 25 psi (172 kPa). Many building codes and the ASME A112.19.2
fixture standard list Maximum static water presssure as 80 PSI (552 kPa).
Closet Flushometer
for 1½” Back Spud
• MODELS 120, 121 & 122
Urinal Flushometer
for 1¼” Top Spud
• MODEL 180
Urinal Flushometer
for ¾” Top Spud
• MODEL 186
Closet Flushometer for 1½”
Top Spud
• MODELS 110/111, 113, 114, 115 & 116
Service Sink Flushometer for
1½” Top Spud
• MODEL 117
PRIOR TO INSTALLATION
TOOLS REQUIRED FOR INSTALLATION
• Straight blade screwdriver
• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench
WITH THE EXCEPTION OF CONTROL STOP INLET, DO NOT
USE PIPE SEALANT OR PLUMBING GREASE ON ANY VALVE
COMPONENT OR COUPLING!
!!! IMPORTANT !!! PROTECT THE FINISH OF SLOAN FLUSHOMETERS — DO
NOT USE TOOTHED TOOLS TO INSTALL OR SERVICE
THESE VALVES. USE A SLOAN A-50 SUPER-WRENCH™,
SLOAN A-109 PLIER WRENCH OR SMOOTH JAWED SPUD
WRENCH TO SECURE ALL COUPLINGS. ALSO SEE “CARE
AND CLEANING” SECTION OF THIS MANUAL.
!!! IMPORTANT !!!
THIS PRODUCT CONTAINS MECHANICAL AND/OR
ELECTRICAL COMPONENTS THAT ARE SUBJECT TO
NORMAL WEAR. THESE COMPONENTS SHOULD BE
CHECKED ON A REGULAR BASIS AND REPLACED AS
NEEDED TO MAINTAIN THE VALVE’S PERFORMANCE.
!!! IMPORTANT !!!
If you have questions about how to install your
Sloan flushometer, consult your local
Sloan Representative or call Sloan Technical Support at:
1-888-SLOAN-14 (1-888-756-2614)