Sloan 952 Royal Concealed 900 Hydraulic Series - Manual

PRIOR TO INSTALLATION
TOOLS REQUIRED FOR INSTALLATION
Code No. 0816301
Rev. 3 (05/13)
INSTALLATION INSTRUCTIONS FOR SLOAN SERIES 900 HYDRAULIC FLUSHING
SYSTEM — ROYAL ® AND REGAL ® XL CONCEALED CLOSET AND URINAL INSTALLATIONS
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and
workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase.
During this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under
normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No
claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE
FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
Concealed Closet Flushometer
1-1/2” (38 mm) Back Spud
MODEL 940
MODEL 952
Concealed Closet Flushometer
No-Flush Connection
MODEL 950
Concealed Closet Flushometer
1-1/2” (38 mm) Top Spud
MODEL 953
Concealed Urinal Flushometer
1-1/4” (32 mm) Back Spud
MODEL 990
Concealed Urinal Flushometer
3/4” (19 mm) Back Spud
MODEL 995
Model 952 Model 995
Prior to installing Sloan’s Flushometer, install the items listed below as illustrated
in the Rough-in Diagrams on Pages 2 and 3.
• Bore a 2” (51 mm) hole in wall for piping, if required.
• Install closet or urinal fixture.
• Install 1-1/2” (38 mm) drain line (NOT supplied by Sloan).
• Install water supply line.
• Bore a 1-1/2” (38 mm) hole in wall for Hydraulic Push Button Actuator.
• For Model HY-72-A Push Button Actuator, install an electrical box at the Push
Button Actuator location.
IMPORTANT:
• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES
AND REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE
VOLUME OF WATER FOR EACH FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
Sloan Royal and Regal XL Flushometers are designed to operate with 10 to 100
psi (69 to 689 kPa) of water pressure.
THE MINIMUM PRESSURE REQUIRED
TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE SELECTED.
Consult fixture manufacturer for minimum pressure requirements.
Most Low Consumption water closets (1.6 gpf/6.0 Lpf) require a minimum
flowing pressure of 25 psi (172 kPa).
IMPORTANT: With the exception of Control Stop Inlet, DO NOT use pipe
thread sealant or plumbing grease on valve components or couplings!
IMPORTANT: Protect the chrome or special finish of this flushometer —
DO NOT use toothed tools to install or service the valve. Also, see “Care
and Cleaning” section of this manual.
• Straight blade (flathead) screwdriver
• 5/64” hex wrench • Parker Tube Cutter (PTC)
• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed
spud wrench