Using the panel heater, 2) fixing the comfort temperature, 3) fixing the eco temperature – Thermor Variations de Silhouette User Manual
Page 26: 4) frost-free mode, 5) the heating indicator : v1, 6) switching off the device, 7) locking the controls
USING THE PANEL HEATER
1) Description of the control unit :
9
9
9
9
9
➔ Mode switch knob.
➔ COMFORT temperature set value adjustment knob.
➔ ECO temperature set value adjustment knob.
V1 ➔ Heating light.
V2 ➔ COMFORT mode light.
V3 ➔ ECO light.
2) Fixing the comfort temperature :
The comfort temperature that you would like while the room is occupied.
a) Set the cursor
to
,
the heating light V2 comes on.
b) Set the control knob to 5, the heating light V1 comes on, if the room temperature is below the required temperature.
c) Wait a few hours until the temperature stabilizes.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position.
If the setting is not satisfactory, adjust it and start again from point c.
3) Fixing the Eco temperature :
This involves a reduction in degrees compared to the Comfort temperature. We recommend that you use this mode for
periods of absence of more than 2 hours or overnight.Warning: This reduction applies to the Comfort temperature so it is
important to set the Comfort temperature first, before setting the Eco reduction.
a) Set cursor to , indicator light V3 lights up.
b) Set the knob to –3.5°, the heating indicator light V1 comes on if the ambient temperature is less than the desired Eco
temperature.
c) Wait a few hours until the temperature stabilizes.
d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position.
If the setting is not satisfactory, adjust it and start again from point c.
NB: The measurement is set to –3.5°C in our laboratories. It is possible that the setting for the reduction is not precisely
–3.5°C, depending on your installation’s particular characteristics. In this case, adapt the setting to obtain the desired
reduction.
4) Frost-Free mode :
This mode is used to keep the temperature at approximately 7°C in the room when you are absent from the house for a
prolonged period (i.e. more than 24 hours).
a) Set the cursor to
.
5) The heating indicator : V1
This light indicates periods during which the element is heating. It flashes when the temperature is stable, and it goes off
if the temperature is too high.
6) Switching off the device :
To set the device to the Off position, move the cursor to .
7) Locking the controls :
It is possible to lock or limit the range of use of thumb-wheels and and lock selector switch cursor to prevent the
inadvertent manipulation of the device (by children, etc).
a) Detach the device from its wall bracket.
b) On the back of the thermostat box, detach pins P from their supports.
c) Choose position B to lock the thumb-wheels or position L to limit the range of use of the thumb-wheels.
Choose one of the positions M to lock the person in the desired mode.
s
d
n
a
m
m
o
C
d
e
v
i
e
c
e
R
t
n
e
r
r
u
c
o
N
o
n
n
o
i
t
a
n
r
e
t
l
A
)
''
7
5
'
4
(
t
n
e
r
r
u
c
)
''
3
(
V
0
3
2
e
s
a
h
p
o
n
n
o
i
t
a
n
r
e
t
l
A
)
''
3
5
'
4
(
t
n
e
r
r
u
c
)
''
7
(
V
0
3
2
e
s
a
h
p
e
t
e
l
p
m
o
C
V
0
3
2
n
o
i
t
a
n
r
e
t
l
a
-
f
l
a
h
e
v
i
t
a
g
e
N
V
5
1
1
-
n
o
i
t
a
n
r
e
t
l
a
-
f
l
a
h
e
v
i
t
i
s
o
P
V
5
1
1
+
n
o
i
t
a
n
r
e
t
l
a
e
p
o
c
s
o
ll
i
c
s
O
l
a
r
t
u
e
N
/
f
é
R
e
d
o
M
d
e
n
i
a
t
b
o
t
r
o
f
m
o
C
C
°
1
-
t
r
o
f
m
o
C
C
°
2
-
t
r
o
f
m
o
C
o
c
E
e
z
e
e
r
f
-
i
t
n
A
p
o
t
S
t
u
C
r
e
w
o
P
Table of commands the panel heater can receive on its pilot wire. To be measured between the pilot wire and the neutral.
2-4) Lock the appliance on the hook-on bracket
6
6
6
6
6
080214_CEETvariation_ang.PMD
14/12/2007, 08:02
2