Thinklogical StudioPRO Extender Single Link Quick Start Guide - Manual

QUICK START GUIDE
StudioPRO Extender
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
Visit us online at www.thinklogical.com for more product information,
current updates and the complete line of Thinklogical™ products.
+
_ 5VDC
DVI FROM CPU
L1 L3
DVI LOCAL
DISPLAY
USB 2.0
POWER
+
_
5VDC
DVI TO
DISPLAY
L3 L1
DVI TO DISPLAY
(DDC)
USB 2.0
POWER
1
2
3
4
StudioPRO SINGLE-LINK EXTENDER RECEIVER
The Future of Access and Control
DDC MODE
LCL REM
ACQUIRE
SELECT
HOST LINK POWER STATUS
StudioPRO Extender
Single-Link DVI, USB 2.0
Fiber optic transmitter
MRTS Technology
Powered by
The Future of Access and Control
DDC MODE
LCL REM
ACQUIRE
SELECT
HOST LINK
POWER STATUS
StudioPRO Extender
Single-Link DVI, USB 2.0
Fiber optic receiver
MRTS Technology
Powered by
1
2
3
4
Single-Link DVI, USB 2.0 Video Extension System
StudioPRO SINGLE-LINK EXTENDER TRANSMITTER
DVI Local
Display
DVI TO Display
(DDC)
DVI TO Display
USB Devices
3
1
4
5
STEP 1: Install any USB
peripheral devices to the
receiver’s USB 2.0 ports.
STEP 2: Connect the output
display device(s) to the receiver’s
DVI TO DISPLAY ports. The DDC
port is the PRIMARY port and should
be used when there is only one
display device connected.
STEP 3: Connect the supplied
+5V power supply (PWR-000022-R)
to the receiver and plug it into a
standard AC source.
STEP 4: Connect
your multi-mode fiber-
optic cables between
the transmitter and
receiver units (up to
1000 meters).
2
LCL REM DDC MODE DESCRIPTION
REMOTE
DYNAMIC
REMOTE
STATIC
PASS-
THRU
LOCAL
STATIC
Acquire Button
Used to initiate DDC collection. Works with all modes except Pass-Thru. Must
be pressed after switching between DDC modes.
Select Button
Used to select the DDC mode. The modes will cycle through Remote
Dynamic, Remote Static, Pass-Thru and Local Static.
Both Buttons held 5 seconds
Holding both buttons for 5 seconds will reload the default DDC table into the
Tx and switch to Remote Static mode.
OFF GREEN
GREEN
GREEN GREEN
GREEN
ORANGE
ORANGE
EDID read from remote display and updated
each time remote display changes.
EDID read from remote display when
acquire button is pressed.
Acts as a direct connection between CPU
and display. No emulation is performed.
EDID read from local display when
acquire button is pressed.
STEP 5: Connect the supplied +5V power
supply (PWR-000022-R) to the transmitter
and plug it into a standard AC source.
CONTENTS:
StudioPRO Single-link Extender Transmitter [1]
StudioPRO Single-link Extender Receiver [1]
USB A-B cable, 6' (CBL-000015-006FR) [1]
DVI-D (M to M) cable, 2M (CBL-000009-002MR) [1]
Universal Power Supply (PWR-000022-R) [2]
StudioPRO Extender Product Manual
CPU
6
7
STEP 6: Connect your
local monitor to the
transmitter’s DVI
LOCAL DISPLAY port.
STEP 7: Connect your
USB and DVI cables
from the CPU to the
transmitter. Ensure all
system functions are
operating properly.
StudioPRO_Extender_Single-link_Quick_Start_Rev_B
DVI FROM CPU