Thinklogical SDIXtreme 3G+ Rack Model Quick Start Guide User Manual
Sdi xtreme, Quick start guide, Vx 160
110-240V ~, 0.5A, 50/60 Hz
Caution! Remove both cords before servicing
3G SDI Fiber Optic Extension
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
TX
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
A
L
A
R
M
A
L
A
R
M
A
L
A
R
M
A
L
A
R
M
TX
RX
RX
Two Inputs, Two SFPs
One Input with
Loop Out, One SFP
SDI
Xtreme
Rack-Mount 3G SDI Fiber Optic Extension
3G+
SDIXtreme3G+_Rack_Mount_VX160_Quick_Start_Rev_A
QUICK START GUIDE
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
Visit us online at
www.thinklogical.com
for more product information, current literature and
the complete line of Thinklogical
™ products.
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
STEP 3:
Connect your 3G or SD/HD SDI source devices to
the Transmitter IN Ports and destination devices to the
Receiver OUT Ports. If using RS422, connect your devices
to the RS422 ports located directly above the BNC ports.
Ensure all system functions are operating properly.
STEP 2:
Install each unit’s provided AC Power
Cords and plug them into standard AC sources.
On the SDI Extenders, ensure that each
module’s ACTIVE LED comes on. The ACTIVE
LED will blink if no SDI input is present.
2
3
The Logical Solution
– Rack-Mount Serial Digital Interface Extension.
The SDI
Xtreme
product series is a compact, broadcast quality, SDI over fi
ber extension system.
The rack mountable system is
designed to transmit one 3G
(2.97 Gb/s)
or two SD
(270 Mb/s)
/HD
(1.485 Gb/s)
SDI signals
(including dual-link)
per module
, up to four
modules per chassis, with or without embedded audio and data, and is SMPTE 424M, 292M, 259M, 372M and 425 level A and B compliant. In addition, this
fiber based
transport system gives users the assurance that each signal is immune to video pathological signals over the entire length of the
fiber interconnect, while supporting all
pathological patterns at all rates using standard SFPs. The system also supports either single or multi-mode
fiber and is fully compatible with Thinklogical’s VX and HDX
Router line of products.
3G+
enter
POWER OK
POWER OK
3G SDI Fiber Optic Extension
SDI
Xtreme
3G+
110-240V ~, 0.5A, 50/60 Hz
Caution! Remove both cords before servicing
3G SDI Fiber Optic Extension
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
RX
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
CH0
SDI
CH1
SDI
RS422
SFP0
SFP1
HD
SD
ACT
3G
CH0 CH1
A
L
A
R
M
A
L
A
R
M
A
L
A
R
M
A
L
A
R
M
RX
SD, HD SDI Source 4
SD, HD SDI Source 5
3G SDI Source 6
SD, HD SDI Source 4►
3G SDI Source 6►
SD, HD SDI Output 4
SD, HD SDI Output 5
3G SDI Output 6 (1)
RS422
RS422
Pan/Tilt/Zoom Controller
1
2
3
4
1
2
3
4
5
6
7
SD, HD SDI Source 3
SD, HD SDI Source 2
3G SDI Source 1
SD, HD SDI Output 3
SD, HD SDI Output 2
3G SDI Output 1 (1)
RS422
RS422
Pan/Tilt/Zoom
Controller
Machine
Controller
◄3G SDI Source 1
Machine
Controller
1
STEP 1:
Connect each
module’s Fiber Optic
Cables OUT to any Router Receive
Ports. If using RS422, connect
each module’s Fiber Optic Cables
IN to any Router Transmit Ports.
KVM Matrix Switch
VX
160
router
TX
TX
Source 6
Loop Out
3G SDI Output 6 (2)
Source 1
Loop Out
3G SDI Output 1 (2)
RS422
►
RS422
►
◄RS422
◄RS422
16 Rack Units, 850 Watts
SDIXtreme 3G+
Chassis 1
SDIXtreme 3G+
Chassis 2
SD,HD SDI Source 5►
Two SDI Outputs, Two SFPs
1
2
3
4
1
2
3
4
5
6
7
◄
◄SD, HD SDI Source 2
& 3
Two De-Multiplexed
Outputs, One SFP
Two Multiplexed Inputs, One SFP
One Input with Loop Out, One SFP
Two SDI Outputs,
One SFP
Two SDI Outputs, One SFP
Each Rack-mountable 3G SDI Extender Chassis holds four interchangeable Transmitter or Receiver modules.
Each module
can support one 3G or two SD/HD signals (including dual-link) and one RS422 back-channel
. Each chassis is powered by
dual hot-swappable, current sharing power supplies that are accessed from the front panel (below).
In the above example:
CHASSIS 1
is equipped with one
Two-Input Transmitter
, one
Single-Input with Loop Out
Transmitter
, one
Two-Output/Two SFP Receiver
and one
Two De-Multiplexed-Output/One SFP Receiver
module.
CHASSIS 2
is equipped with one
Two-Output/Two SFP Receiver,
one
Two-Output/One SFP Receiver,
one
Single-Input
with Loop Out Transmitter
and one
Two Multiplexed-Input Transmitter
module.
All signals are shown routed through Thinklogical’s VX160 KVM Matrix Switch.
Use the front LCD Panel
to verify your current
module configuration.