Thinklogical Velocitykvm-5 Single-mode Quick Start Guide - Manual

100-240V-,0.5A, 50/60 Hz T 2A ,250VAC
CAUTION! Replace with same type and rating fuse.
CNTRL
LINE OUT HOST
USB HID
U
P
D
A
T
E
S
PWR FOL
USB 2.0
SER IAL PORT L1
RGB/DVI OUT DDC RGB/DVI OUT
STEP 6: An RGB/DVI-D cable (CBL000013-
002MR) is included. Connect it to the CPU RGB/
DVI Video Card and the other end to the
VelocityKVM Transmitter’s RGB/DVI IN connector.
STEP 7: (Optional) Connect your
local monitor cable (not included) to
the RGB/DVI OUT connector on the
VelocityKVM Transmitter.
UPDATES
DEV
RGB/DVI OUT RGB/DVI IN
SER IAL PORT L1
LINE IN
MIC OUT HID
P
S
2
P
S
2
LOCAL FROM CPU
U S B 1 .1
U S B 1 .1
USB HID
HOST
CNTRL
CAUTION! Replace with same type and rating fuse.
100-240V-,0.5A, 50/60 Hz T 2A ,250VAC
CLINK
PWR
CP FOL
1
3 USB 2.0
Audio OUT►
◄Audio IN
PS/2 Keyboard
PS/2 Mouse
USB HID (Kybd/Mouse)
USB 1.1 (Kybd/Mouse)
Audio IN
PS/2
Keyboard/
Mouse
USB HID
USB 1.1
9
RGB/DVI
IN
Audio OUT
5
2
3
Velocity KVM-5 Transmitter
Velocity KVM-5 Receiver
STEP 8: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
USB HID connectors into the VelocityKVM
Transmitter’s local devices receptacles.
STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.
STEP 5: Connect
your KVM devices
to the CPU using
the cables supplied
in KIT-000005-R.
STEP 3: Turn the
Receiver unit ON.
STEP 9: Turn the
Transmitter unit ON.
STEP 2: Connect your desktop devices
(monitors, keyboard, mouse, etc.) to the
Receiver using standard cables.
The Thinklogical™ Velocity kvm-5 RGB/DVI Single-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by one single-
mode fiber optic cable up to 40 kilometers. The transmitter unit connects to the computer with standard cables and the receiver unit provides connections
to the user interface devices. The Velocity kvm-5 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and USB 1.1. USB
2.0 (high speed up to 480Mbps) is optional.
Note: Be sure to
leave adequate ventilation
space on both sides of
the units (2” minimum),
especially if the units are
being stacked
CONTENTS
Upon receiving your Thinklogical™
Velocity kvm-5 Extender you should
find the following items:
· VelocityKVM Extender Transmitter
· VelocityKVM Extender Receiver
· 2 AC power cords, PWR-000006-R
(International connections may differ.)
· VelocityKVM Extender Cables:
1 DVI-I Male Cable, 2 meters, CBL000013-002MR
1 HD15 to DVI Cable, 2 meters, CBL-000022-002MR
1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R
· VelocityKVM Single-Mode Extender Product Manual
All physical connections to the product use industry-standard connectors.
8
QUICK START GUIDE
PS/2 Connector USB HID Connector
10
STEP 10: Turn on the
Source (CPU) last. Verify
that all system features are
functioning properly.
Visit us online at www.thinklogical.com for more
product information, current updates and the
complete line of Thinklogical products.
MIC IN
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
Velocity kvm-5
Single-Mode Fiber Extension System – RGB/DVI Display
4
8 Mounting bracket
screws
Single Head Single Link Velocity kvm-4
Fiber Optic Transmitter
2 Mounting bracket screws
in four places.
RACK-MOUNT OR DESK-TOP
OPTIONS: Like all Thinklogical
™
KVM extenders, the Velocity KVM-5
can be mounted in a standard EIA 19"
rack or on a shelf or desk-top.
VEL-U00S05-SCRX
VEL-U00S05-SCTX
STEP 4: Connect your Single-Mode Fiber
Optic cable between the Transmitter and
Receiver units as shown (up to 40 Kilometers).
(Use APC-SC fiber connectors only)
VelocityKVM
Extenders are designed and
identified as CLASS 1 LASER
products. Class 1 laser
products do not require
special precautions under
conditions of normal use.
Each mounting bracket is secured
by four screws and can be safely
removed from the transmitter or
receiver unit for desk-top mounting
after power has been removed from
the unit.
All screws should be reinstalled after
the brackets have been removed.
RGB/DVI
Display Out
RGB/DVI Display
Out DDC
Local
Display
VELOCITY-5_Single_Mode_Quick_Start_Rev_A
5
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
6
7