Thinklogical Velocitykvm-24 Quick Start Guide - Manual

1 0 0 - 2 4 0 V - , 0 . 5 A , 5 0 / 6 0 H z T 2 A , 2 5 0 V A C
C A U T I O N ! R e p l a c e w i t h s a m e t y p e a n d r a t i n g f u s e .
C N T R L
L I N E O U T H O S T
U S B H I D
U
P
D
A
T
E
S
P W R F O L
U S B 2 . 0
S E R I A L P O R T
L 1 L 3
D V I O U T 1 D D C D V I O U T 1 D V I O U T 2 D D C D V I O U T 2
STEP 6: Two DVI-D cables (CBL000009-002MR) are included.
Connect one each to the CPU DVI 1 and DVI 2 Video Cards and the
other ends to the VelocityKVM Transmitter’s DVI IN 1 and 2
Connectors.
STEP 7: (Optional) Connect your local monitor 1 and local monitor 2 DVI
cables (not included) to the DVI OUT 1 and DVI OUT 2 connectors on the
VelocityKVM Transmitter.
U P D A T E S
D E V
D V I O U T 1 D V I O U T 2 D V I I N 2 D V I I N 1
S E R I A L P O R T L 1 L 2 L 3
L I N E I N
M I C O U T H I D
P
S
2
P
S
2
L O C A L F R O M C P U
U S B 1 . 1
U S B 1 . 1
U S B H I D
H O S T
C N T R L
C A U T I O N ! R e p l a c e w i t h s a m e t y p e a n d r a t i n g f u s e .
1 0 0 - 2 4 0 V - , 0 . 5 A , 5 0 / 6 0 H z T 2 A , 2 5 0 V A C
C L I N K
P W R
C P
F O L
5
U S B 2 . 0
A u d i o O U T ►
A u d i o I N ◄
P S / 2 K e y b o a r d
P S / 2 M o u s e
U S B H I D ( K y b d / M o u s e )
U S B 1 . 1 ( K y b d / M o u s e )
Audio IN►
PS/2
Keyboard/
Mouse
USB
HID
USB 1.1
9
D V I I N 2
D V I
I N 1
D V I O U T 1 D V I O U T 2
▲
Audio
OUT 5
Display 2
2
3
VelocityKVM-24 Transmitter
VelocityKVM-24 Receiver
STEP 8: If desired, connect your local
keyboard and mouse by inserting the PS/2 or
USB HID connectors into the VelocityKVM
Transmitter’s local devices receptacles.
STEP 4: Connect
your Multi-Mode
Fiber Optic
cables between
the Transmitter
and Receiver:
L1/Tx to L1/Rx
L2/Tx to L2/Rx
L3/Tx to L3/Rx
STEP 5: Connect
your KVM devices
to the CPU using
the cables supplied
in KIT-000005-R.
STEP 3: Turn the
Receiver unit ON.
STEP 2: Connect your desktop
devices (monitors, keyboard, mouse,
etc.) to the Receiver using standard
cables.
Each Thinklogical™ Velocity kvm-24 Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by three multi-mode fiber
optic cables (or by one optional single-mode fiber). The transmitter unit connects to the computer with standard cables and the receiver unit provides
connections to the user interface devices. The Velocity kvm-24 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports and
USB 1.1. Options include USB 2.0 (high speed up to 480Mbps).
Note: Be sure to leave
adequate ventilation space
on both sides of the units
(2” minimum), especially if
the units are being stacked
CONTENTS
Upon receiving your Thinklogical
Velocity kvm-24 Extender, you
should find the following items:
VelocityKVM Extender Transmitter
VelocityKVM Extender Receiver
2 AC power cords, PWR-000006-R
(International connections may differ.)
VelocityKVM Extender Cables:
2 DVI-D Male Cables, 2 meters, CBL000009-002MR
1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R
VelocityKVM Extender Product Manual
All physical connections to the product use industry-standard connectors.
L 1 L 2 L 3
L 1 L 2 L 3
QUICK START GUIDE
PS/2 Connector USB HID Connector
10
STEP 10: Turn on the
Source (CPU) last. Verify
that all system features are
functioning properly.
Visit us online at www.thinklogical.com for more
product information, current updates and the
complete line of Thinklogical products.
T M
M I C I N
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
STEP 9: Turn the
Transmitter unit ON.
8 Mounting bracket
screws
DV I TWO DIS PLA Y
Velocity kvm-24
Fiber Opt ic T ransmitter
2 Mounting bracket screws
in four places.
RACK-MOUNT OR DESK-TOP
OPTIONS: Like all Thinklogical™
KVM extenders, the Velocity KVM-24
can be mounted in a standard EIA 19"
rack or on a shelf or desk-top.
Each mounting bracket is
secured by four screws and
can be safely removed from
the transmitter or receiver
unit for desk-top mounting.
8
6
7
DVI
Display 1
DVI
Display 2
Local
Display 1
Local
Display 2
PS/2 or HID
Connectors
Veloc i ty kvm-24
Multi-Mode Fiber Extension – DVI Two Display
VEL-U00M24-SCTX
VEL-U00M24-SCRX
L1: Data Tx to Rx and Video 1
L2: Data Rx to Tx
L3: Video 2
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
4
L 2
VELOCITY-24_Quick_Start_Rev_B
STEP 1: Ensure that the POWER ON/OFF switch is
in the OFF position (0) on both the Tx and Rx units.
Connect the supplied AC Power Cords to both units
and plug them into a standard AC supply. LEAVE
BOTH SWITCHES IN THE OFF POSITION.
1