Thinklogical Velocityrgb System-9 Quick Start Guide - Manual

DVI-D Connector 1 DVI-D Connector 2
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
PHONE: (800) 291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
All physical connections to the product use industry-standard connectors.
Visit us online at www.thinklogical.com for more product information, current updates
and the complete line of Thinklogical products. TM
Transmitter
Receiver
Local
Display
Optical Fiber Ports available for
ST-, SC- or LC-type connectors.
Video Extension System -
Thinklogical’s™ Video Extension System-9 supports RGB video formats up to 165 MHz and provides high resolution video extension for secure computer installations. It is now
possible to position your remote monitor in any setting from office to lecture hall to boardroom while keeping the computer secure in a remote, controlled location. With dual RGB outputs on the
Receiver, the video source can be distributed to two separate displays, eliminating the need for an external distribution amplifier.
Contents
Upon receiving your Thinklogical™
VelocityRGB Extender Transmitter
VelocityRGB Extender Receiver
HD15M to HD15M Cable, 2 Meters (CBL-000020-002MR) – Qty 1
3.5 mm Audio cable (CBL-000016-002MR) – Qty 2
RS-232 Serial Cable (CBL-000017-002MR) – Qty 1
Universal AC Power Adapters (PWR-000022-R) – Qty 2
RGB Extender Product Manual
STEP 4
Connect the fiber optic cables between the
Transmitter and Receiver Units (up to 1000
meters). Do not kink or pinch the cables and be
sure to keep all bend radii to less than 3 inches.
STEP 3
Connect the supplied AC Power Adapter
(PWR-000022-R) to the Receiver and plug it
into a standard AC source. STEP 1
Install one or two VGA
monitors by connecting
their HD15 cables to the
VGA 1 and/or VGA 2
ports on the Receiver.
STEP 5
Connect the CPU’s RGB video OUT
to the Transmitter with the supplied
HD15M to HD15M cable (CBL-000020-
002MR) and connect the CPU’s audio
IN/OUT with standard 3.5mm audio
cables. Connect the DB9 Serial Port
from CPU to TX, if used.
When lit, the green LED indicates
that +5VDC power is applied.
(Applies to both Tx and Rx units.)
The Transmitter and
Receiver USB ports are
for firmware upgrades
available from
Thinklogical™.
enter
Velocity rgb
Video Extension System - 9 Technology
Powered by
MRTS
Receiver
enter
Velocity rgb
Video Extension System - 9
Transmitter
SERIAL PORT
+
_
5VDC
L1 L2
FIBER
TO LOCAL
DISPLAY
FROM CPU
LOS
LINE IN
MIC OUT DOWNLOAD
POWER
CNTRL
SERIAL PORT
+
_
5VDC
L2 L1
FIBER
VGA 2
VGA 1
LOS
LINE OUT
MIC IN
DOWNLOAD
POWER
CNTRL
Technology
Powered by
MRTS
VGA 1 VGA 2
Audio OUT
Audio IN
RGB from CPU
STEP 2
Connect your audio input/output
devices to the Receiver’s
3.5mm audio ports and, if used,
connect the DB9 Serial Port
from Rx to device.
STEP 7
Connect the supplied AC Power
Adapter (PWR-000022-R) to the
Transmitter unit and plug it into a
standard AC source.
STEP 6
If desired, connect a local VGA
monitor to the Transmitter with an
HD15M to HD15M cable.
STEP 8
Turn on the CPU last.
Verify that all system
features are functioning
properly.
Both units feature a DB9 Serial
Port to support serial connections
from the CPU to the Transmitter
and from the Receiver to the
user’s serial device.
When lit, the LOS
(Loss Of Signal) LED
on each unit indicates
loss of a valid video
signal.
Local keyboard and mouse
Power Supply
Power Supply
VGA 2
VGA 1
Rev.B 5/09