Thinklogical VX40 Velocitykvm-24 Separate Data Path Quick Start Guide - Manual

DVI IN
1
Source CPU
Network Hub
Optional Secondary Controller Card
IP address: 192.168.13.16
Primary Controller Card
IP Address: 192.168.13.15
1
2
3
4
5
6
7
8
9
10
POWER SUPPLY 1 (LEFT):
POWER SUPPLY 2 (RIGHT):
FANS:
TEMPERATURE WARNING:
TEMPERATURE SHUTDOWN:
CPU:
INPUT/OUTPUT CARDS:
ANY OF THE ABOVE
COMMON
GROUND
The VX 40 Router Critical Hardware Alarms: (Located at the top, left rear of the unit.)
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption and module removed
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption and module removed
Individual fan monitoring
Chassis over temperature, multiple sensors
Chassis over temperature causing shutdown
Card failure (Only with a redundant card)
SFP+ failure, laser output fault
STEP 1: Connect your VelocityKVM-24 Dual Data Port Receiver to the VX 40 using
multi-mode fiber-optic cables (up to 1000 meters). Connect L1 and L3 to any Downstream
Transmit Ports. Connect K1 to any Downstream Receive Port and K2 to the same
numbered Downstream Transmit Port.
STEP 2: Ensure that the Receiver’s ON/OFF switch is in the OFF (0) position. Insert the
AC power cord into the Receiver and plug it into a standard AC source. Turn the unit ON.
STEP 3: Depending on your configuration, connect your desktop devices (monitors,
keyboard, mouse, stereo 3D, etc.) to the Receiver using standard cables as shown in the
examples below. Turn all the devices ON.
STEP 8: Connect both supplied AC Power Cords (PWR-0000006-R)
to the receptacles located on the VX 40's power supplies. Plug each
one into a standard AC source. Verify that all system functions are
operating properly.
Copyright © 2011. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical™ products.
VX40_Vel-24D_QSG
VEL-00DM24-LCTX
Velocity-24 Dual Data Port Transmitter
Stereo 3-D
◄Audio IN
Audio OUT►
USB HID
PS2 Mouse
PS2 Keyboard
VelocityKVM-24D Receiver
VEL-00DM24-LCRX
Keyboard and Mouse to
PS2 or USB HID Ports
L1: Video 1
L3: Video 2
K1: Data RX to TX
K2: Data Tx to Rx
External Control CPU
Stereo 3D
Emitter OUT
USB 2.0 OUT
2
3
4
5
6
7
Thinklogical’s™ VX40 KVM Matrix Switch features
redundant Power Supplies and Controller Modules
for uninterrupted performance, even during system
reconfiguration, updates or debug. The VX40
remains fully functional with only one Power Supply
installed or with one Controller activated.
NOTE: When using a single Controller, the module
on the left (Primary) must be used.
Thinklogical’s™ VX 40 KVM Matrix Switch features
redundant Power Supplies and Controller Modules
for uninterrupted performance, even during system
reconfiguration, updates or debug. The VX 40
remains fully functional with only one Power Supply
installed or with one Controller activated.
NOTE: When using a single Controller, the module
on the left (Primary) must be used.
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected] Extend Distribute Innovate Extend Distribute Innovate
1
DVI IN
2
USB 2.0
QUICK-START GUIDE QUICK-START GUIDE
Complete steps 1 through 9 to connect your Thinklogical™ VX40 Router KVM Matrix Switch Complete steps 1 through 8 to connect your Thinklogical™ VX40 Router KVM Matrix Switch
As used with Thinklogical’s™ Velocitykvm-24D
Dual Data Port Fiber Extension System
As used with Thinklogical’s™ Velocity kvm-24D
Dual Data Port Fiber Extension System
STEP 4: Connect your VelocityKVM-24 Dual Data Port Transmitter to the VX 40 using multi-mode
fiber-optic cables (up to 1000 meters). Connect L1 and L3 to any Upstream Receive Ports. Connect
K1 to any Upstream Transmit Port and K2 to the same numbered Upstream Receive Port.
STEP 5: Ensure that the Transmitter’s ON/OFF switch is in the OFF (0) position. Insert the AC
power cord into the Transmitter and plug it into a standard AC source. Turn the unit ON.
STEP 6: Connect the DVI cables from the Source CPU to the Transmitter’s DVI IN 1 and 2 Ports. If
desired, connect a local monitor to each of the Transmitter’s two DVI OUT ports with standard DVI
cables. Connect an optional Keyboard & Mouse to the local USB or PS2 Ports. Connect your
peripheral devices from their source to the Transmitter Inputs with standard copper cables. Ensure
the CPU is turned ON.
STEP 7: Connect the VX 40 Controller Cards’ LAN Ports to your Controller CPU with CAT5 cables.
(CPU IP address: 192.168.13.9)
8
KVM Matrix Switch
Powered by
MRTS Technology
VX 40
router
DVI OUT 1
DDC
DVI OUT 1
DVI OUT 2
DDC
DVI OUT 2
Local
DVI OUT 1
Local
DVI OUT 2
Local Keyboard and Mouse
to PS2 or USB HID Ports