Thinklogical VX40 Velocitykvm-5 Velocitykvm-24 Quick Start Guide - Manual

QUICK-START GUIDE
VX40 Router KVM Matrix Switch Chassis, 6 Rack Units, 400 Watts
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical products.
Single-Head, Single-Link RGB / KVM Source
KVM Matrix Switch
Powered by
MRTS Technology
TM
Single-Head, Single-Link RGB / KVM Destinations
VX 40
router
QUICK-START GUIDE
STEP 8: (Final step) Connect both supplied AC Power Cords (PWR-0000006-R)
to the receptacles located on the
VX 40's power supplies. Plug each one into a
standard AC source. Verify that all system functions are operating properly.
8
7
L1
L2
VX40_VEL-24_VEL-5_BLACK_BOX_Quick_Start_Rev_B PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
1
2
3
4
5
6
7
8
9
10
POWER SUPPLY 1 (LEFT):
POWER SUPPLY 2 (RIGHT):
FANS:
TEMPERATURE WARNING:
TEMPERATURE SHUTDOWN:
CPU:
INPUT/OUTPUT CARDS:
ANY OF THE ABOVE
COMMOM
GROUND
The VX 40 Router Critical Hardware Alarms: (Located at the top, left rear of the unit.)
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption and module removed
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption and module removed
Individual fan monitoring
Chassis over temperature, multiple sensors
Chassis over temperature causing shutdown
Card failure (Only with a redundant card)
SFP+ failure, laser output fault
As used with Thinklogical’s™ Velocity kvm-5 and the Velocity kvm-24
Video Extension Systems
100
-240
v –
50 /60 Hz 12A
100-
24 0v – 50/60 Hz 12A
ALARM
UPSTREAM DOWNSTREAM CONTROLLER
1-5 6-10 26-30 11-15 16-20 21-25 31-35 36-40 1-5 6-10 26-30 11-15 16-20 21-25 31-35 36-40
5
4
3
2
1
CONSOLE
ACTIVE
RESET
FAULT
L A N
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
CONTROLLER
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R
T
R T
R T
R
T
R
T
R T
R T
R T
R
T
R
T
R T
R T
R T
R
T
R
T
R T
R T
R T
R
T
R
T
R T
R T
R T
R
T
R
POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER
RS232
CONSOLE
ACTIVE
RESET
FAULT
CONTROLLER
RS232
L A N
Thinklogical’s™ VX 40 KVM Matrix Switch features redundant
Power Supplies and Controller Modules for uninterrupted
performance, even during system reconfiguration, updates or
debug. The
VX 40 remains fully functional with only one Power
Supply installed or with one Controller activated.
NOTE: When using a single Controller, the module on the left
(Primary) must be used. *
Primary Controller Card
Optional Secondary Controller Card
*
L2 L1 L3
Linux Operating System
Video 1 & Data
Downstream
Video 2
Video 2
Data Upstream
Data Upstream
Switch
Fabric
SFP+ A
(Video/data IN,
data OUT)
SFP+ A
(Video/data OUT,
data IN)
SFP+ B
(Video IN)
SFP+ B
(Video OUT)
Digital Crosspoint Switch
T
T
T
R
R R
UPSTREAM DOWNSTREAM
Velocity
Tx
DVI / Data
Source
Velocity
Rx
DVI / Data
Destination
Video 1 & Data
Downstream
U
P
D
A
T
E
S LINE OUT
MIC IN
P
S
2
USB HID
HOST
CNTRL USB 1.1
SER IAL PORT
DVI OUT 1 DVI OUT 1 DDC PWR FOL
USB 2.0 VEL-U00M24-SCRX
Receiver
Velocity kvm
Single-Link, DVI 2 Display / KVM
Destinations
2
DVI OUT 1 DDC
DVI OUT 2 DDC
AUDIO
STEP 1: Connect your VelocityKVM Receiver to the VX 40 using multi-
mode fiber-optic cables (up to 1000 meters). Connect L1 to any
Downstream Transmit Ports and L2 to the same numbered Downstream
Receive Port as shown. Connect L3 to any Downstream Transmit Port.
(See the Digital Crosspoint Switch detail diagram, left.)
PS/2 or USB connectors
L2 L1
L2 L1
STEP 2: Ensure that the VelocityKVM Receiver’s ON/
OFF switch is in the OFF (0) position. Depending on your
configuration, connect your desktop devices (monitors,
keyboard, mouse, etc.) to the Receiver using standard
cables as shown in the example below. Turn all the
devices ON. Insert the AC power cord into the Receiver
and plug it into a standard AC source. Turn the unit ON.
L3
L3
USB
2.0
DVI 1
DVI 2
Audio OUT►
USB 1.1 (Keyboard / Mouse)
VEL-U00M24-SCTX
Transmitter
Velocity kvm
DEV
LINE IN
MIC OUT HID
P
S
2
LOCAL
FROM CPU
USB HID
HOST
CNTRL
USB 1.1 UPDATES SER IAL PORT
DVI OUT 1 DVI OUT 2 DVI IN 2 DVI IN 1
L1 L2 L3
CLINK
PWR CP FOL
6
STEP 6: Connect your USB, PS/2
and Audio sources to the
VelocityKVM Transmitter’s inputs.
5
STEP 3: Connect your VelocityKVM
Transmitter to the VX 40 using multi-mode
fiber-optic cables (up to 1000 meters).
Connect cable
L1 to any Upstream Receive
Port and cable L2 to the same numbered
Upstream Transmit Port. Connect L3 to any
Upstream Receive Port. (See the Digital
Crosspoint Switch detail diagram, right.)
STEP 5: Connect the
DVI IN cables from
the CPU to the
VelocityKVM
Transmitter and the
DVI OUT cable(s)
from the transmitter to
the local monitor(s).
L2
STEP 4: Ensure the VelocityKVM
Transmitter’s ON/OFF switch is in the
OFF (0) position. Connect the Power
Cord and plug it into a standard AC
source. Turn the switch ON (1).
Local DVI 1
(optional)
Local DVI 2 (optional)
Optioal local USB or PS/2
Keyboard & Mouse
L1 L3
L1: Video 1 and Data Tx to Rx
L2: Data Rx to Tx
L3: Video 2
PS/2 (Mouse)
PS/2 (Keyboard)
◄Audio IN
Single-Link, DVI 2 Display / KVM Source
DVI OUT 2 DVI OUT 2 DDC
4
3
1
L2
L3 L1
DVI/RGB IN
Local DVI/RGB
Display (optional)
6 4
5
STEP 3: Connect your
VelocityKVM Transmitter to the
VX 160 using multi-mode fiber-optic
cables (up to 1000 meters).
Connect
L1 to any Upstream
Receive Port and L2 to the same
numbered Upstream Transmit Port.
(See the Digital Crosspoint
Switch detail diagram,
below.)
DEV
DVI/RGB OUT DVI/RGB IN SER IAL PORT
L1 L2
LINE IN
MIC OUT HID
P
S
2
LOCAL FROM CPU
USB1.1
USB HID
HOST
CNTRL
CAUTION! Replace with same type and rating fuse.
100-240V-,0.5A, 50/60 Hz T 2A ,250VAC CLINK
PWR CP FOL 3
UPDATES
USB
2.0
Audio OUT►
USB 1.1 (Keyboard / Mouse)
PS/2 (Mouse)
PS/2 (Keyboard)
◄Audio IN
Optional local
USB or PS/2
Keyboard &
Mouse L2 L1
STEP 6: Connect
your KMASS devices
from the Source CPU
to the appropriate
VelocityKVM
Transmitter ports.
STEP 5: Connect the DVI/RGB IN cable from
the CPU to the VelocityKVM Transmitter.
Connect the DVI/RGB OUT cable from the
Transmitter to the local monitor.
STEP 4: Ensure the
VelocityKVM
Transmitter’s ON/
OFF switch is in the
OFF (0) position.
Connect the AC Power
Cord and plug it into a
standard AC source.
Turn the switch ON.
Velocity kvm-5
Transmitter
VEL-U00M05-SCTX
100-240V-,0.5A, 50/60 Hz T 2A ,250VAC
CAUTION! Replace with same type and rating fuse.
CNTRL
LINE OUT
MIC IN
HOST
USB HID
U
P
D
A
T
E
S PWR FOL
USB 2.0
SER IAL PORT L1 L2 P
S
2
USB1.1
DVI / RGB
OUT DDC
DVI / RGB OUT
DVI/RGB OUT DVI/RGB OUT DDC
PS/2 or USB connectors
2
AUDIO
Velocity kvm-5
VEL-U00M05-SCRX
Receiver
STEP 2: Ensure that the VelocityKVM Receiver’s ON/OFF switch is in the OFF
(0) position. Depending on your configuration, connect your desktop devices
(monitors, keyboard, mouse, etc.) to the Receiver using standard cables as
shown in the example below. Turn all the devices ON. Insert the AC power
cord into the Receiver and plug it into a standard AC source. Turn the unit ON.
STEP 1: Connect your
VelocityKVM Receiver
to the
VX 160 using
multi-mode fiber-optic
cables (up to 1000
meters). Connect cable
L1 to any Transmit Port
on any Downstream
card. Connect cable
L2
to the same numbered
Downstream Receive
Port. (See the
Digital
Crosspoint Switch detail
diagram, below.)
L1 L2
L1
L2
1
3
STEP 7: Connect the Controller
Card LAN Port to your Linux
CPU with a CAT5 cable.
(IP address: 192.168.13.15)