Airaid 300-232 - Manual

Installation Instructions
For Part Numbers:
300-232 720-476 Airaid Oiled Media Filter
301-232 721-476 SynthaMax Dry Media Filter - Red
302-232 722-476 SynthaMax Dry Media Filter - Black
303-232 723-476 SynthaMax Dry Media Filter - Blue
2002-12 Dodge Ram 1500
4.7L V8
1. Disconnect the negative battery cable.
2003-12 Models: A) Squeeze the tab on the
intake air temperature sensor wiring connector
on the front or back of the factory resonator, and
disconnect it from the sensor. 02-07 Models: B)
Loosen two hose clamps. One on the back of the
coupler on the throttle body, and one on the air
filter lid side of the flexible intake tube. 2008
Models: Loosen the hose clamp that holds the
flexible tube to the airbox lid. 2004-12 Models:
C) Disconnect the cr ankcase br eather hose
from the air filter lid. 2002 & 2003 Models: Dis-
connect the breather hose from the back of the
resonator. 2. Slide the flexible intake tube off of the airbox lid and
then lift the complete airbox straight up and out of the
vehicle.
3. Turn the factory air box over and remove 3 of
the 4 grommets. They will be reinstalled in the
Airaid Cool Air Box in step #8.
4. Using a 10mm socket, remove the two bolts
(one bolt on 2008 and newer models) that se-
cure the intake resonator to the engine, one on
the drivers side, and one on the passenger side
of the resonator. Grab the resonator with both
hands at the front and push back and up to re-
lease it from the locator grommet on the bot-
tom. Remove the resonator from the vehicle. 5. 2002-07 Models Loosen the factor y hose
clamp on the coupler and remove the coupler
assembly from the resonator. 2003-12 Models
Rotate the air temp sensor counterclockwise and
remove it from the resonator. These parts will be
reinstalled on the Airaid intake tube in step #12.
6. Install the filter gasket (#23) and filter adapter
(#6) onto the Airaid Cool Air Box, or CAB (#3)
as shown using three 1/4” x 5/8” bolts (#8), and
1/4” flat washers (#9). Refer to the line drawing
above for reference.
7. 2004-12 Models: Install the 1/4” NPT x
1/2”Barbed fitting (#18) into the CAB as
shown. 2002-03 Models Install the 1/4” hex
plug (#19) in place of the barbed fitting. 8. Install the factory grommets removed in step
#3 into the bottom of the CAB at the locations
shown here.
Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Cool Air Box 1
4. Urethane Hump Hose 1
5. Silicone Coupler 1
6. Filter Adapter 1
7. Weather Strip 33” 1
8. 1/4-20 X 5/8” Hex Bolt 3
9. 1/4” Flat Washer 3
10. #48 Hose Clamp 2
11. #60 Hose Clamp 2
12. Grommet Plug 1
13. Grommet 1
14. Rubber Cap 1
15. 1/2” x 90° Rubber Elbow 1
16. #14 Speed Clamp 1
17. #16 Speed Clamp 3
18. 1/4”NPT x1/2” Barbed Fitting 1
19. 1/4”NPT Hex Plug 1
20. 1/2” X 3/4” Barbed Connector 1
21. 1/2” x 4 1/2” Breather Hose 1
22. 1/2” x 1/2” Plastic Elbow 1
23. Adapter Gasket 1
A.
B.
C.
Gasket
Adapter
CAB
Filter Adapter Bolts from step #6
9. Remove the two bolts that secure the factory
airbox mounting bracket to the inner fender.
They will be reinstalled in step #10.