Airaid 350-171 User Manual
Installation instructions
Installation Instructions
For Part Numbers:
350-171
700-452 Airaid Oiled Media Filter
351-171
701-452 SynthaMax Dry Media Filter - Red
352-171
702-452 SynthaMax Dry Media Filter - Black
353-171
703-452 SynthaMax Dry Media Filter - Blue
2005-10 Chrysler 300C 2.7L V6, 3.5L V6
2009-10 Dodge Challenger 3.5L V6
2006-10Dodge Charger 2.7L V6, 3.5L V6
2005-08 Dodge Magnum 2.7L V6, 3.5L V6
Component Identification
1.
Airaid Premium Filter
1
2.
MAF Panel
1
3.
Front Panel
1
4.
1/2” x 14” Breather Hose
1
5.
Weather Strip 27’”
1
6.
6-32x5/16” Screw
4
7.
#6 Flat Washer
4
8.
6-32 Keps Nut
4
9.
½” Rubber Elbow 1
10.
#18 Speed Clamp
3
11.
#16 Speed Clamp
3
12.
½”x ½” Connector
2
1. Disconnect the negative battery cable.
Remove the breather hose from the
factory air box lid and valve cover.
2.7L Engines: remove the hard plastic
breather tube at the elbow near the
back of the valve cover.
3.
Remove the airbox lid by pulling the
tabs towards the front of the car. Then,
lift the lid up and slide it forward, and
remove it from the bottom of the air-
box
.
4.
Remove the factory air filter from
the bottom of the airbox.
6.
Slide the 1/2” rubber elbow (#8) on-
to the breather fitting on the side of the
Quick Fit panels. Install 2
#18speed clamps (#9), one over each
end of the elbow, (Do not tighten the
clamps at this time.)
7.
Slide the three tabs on the back of
the Quick Fit panels into the factory
airbox. (For 2005-2006 models, make
sure the 1/2” rubber elbow (#8) slides
onto the valve cover breather nipple.)
Push the front of the Quick Fit panels
down, until the locking tabs snap into
place. 2.7L Engines: Skip to step #9.
2.
Loosen the hose clamp on the facto-
ry intake tube, located at the air box
lid.
5.
Assemble the Quick Fit panels (#2,
#3) using four 6-32x 5/16” screws
(#5), #6 flat washers (#6), and 6-32
keps nuts (#7).
8.
For 2007 3.5L Engines, (shown
above), slide one end of the 1/2”x 1/2”
connector (#10) into the rubber elbow.
Slide the other end into the factory
breather hose. Install one speed clamp
(#9) over the factory breather hose and
1/2” connector as shown.
2007 3.5L Engines
Only
9.
2.7L Engines: Install the two 1/2”
connectors (#12),into each end of the
supplied breather hose (#4). Connect the
breather hose to the rubber elbow on the
Quick Fit Panel using one #18 speed
clamp (#10), and one #16 speed clamp
(#11). Install one #16 speed clamp on the
opposite end of the hose as shown.
2.7L Engines
#18 speed clamp
#16 speed clamps
1/2” connectors
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.