Encore electronic ENC-LIWP - Manual

Multi-Room Audio
Distribution System
ENC-LIWP
Local Input
Wall Plate
Installation
Instructions
1. PRODUCT DESCRIPTION
The Encore local input wall plate (Model ENC-LIWP) serves as a local
audio source input for the Encore Multi-Room Audio Distribution System.
It provides a connection point for a local audio source in the same room
as the keypad, such as an MP3 player or game box. A high quality
analog-to-digital converter encodes analog sources to digital audio and
distributes it to the keypad (Model ENC-DRS).
The wall plate wires directly to the keypad and mounts in a single-gang
J-box. The keypad selects between an audio source connected to the
local input wall plate or from up to four audio sources connected to
source input wall plates (Model ENC-SIWP) wired to the system hub.
The wall plate has two sets of stereo analog audio inputs, a coaxial
digital and optical digital audio input. Analog Input #1 will override audio
signals at any of the Input #2 sources. When the audio signal on Input #1
ceases, the wall plate will switch back to an Input #2 source after about
10 seconds. The input selector switch selects between Input #2 sources.
A set of gain switches is provided to boost low level signals by +4, or
+8 db. The clipping indicator will light if the signal level is too high.
The system features infrared (IR) remote control. An IR repeater system
monitors IR received at each keypad and repeats the remote control signals
to the audio source components through IR emitters connected to the wall
plate’s IR OUT jack. IR emitters are sold in a 4-pack as Model 2171-4.
2. WALL PLATE FEATURES 3. INSTALL JUNCTION BOX
4. ROUTE CAT-5 CABLE FOR WALL PLATE 5. CONNECT CABLE AT KEYPAD 6. SET GAIN SWITCHES (OPTIONAL) 7. CONNECT CABLE TO WALL PLATE
8. INSTALL WALL PLATE 9. CONNECT AUDIO SOURCE 10. POWER UP AND TEST LIMITED WARRANTY
This Linear product is warranted against defects in material and
workmanship for twenty four (24) months.
This warranty extends only
to wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels.
Linear does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer’s warranty, if any.
There are no obligations
or liabilities on the part of Linear LLC for consequential damages
arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property,
revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability
and implied warranties for fitness, are valid only until the warranty
expires.
This Linear LLC Warranty is in lieu of all other warranties
express or implied.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Service at
1-800-421-1587 for an RPA# and other important details.
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
PRINTER’S INSTR
UCTIONS:
INSTR,INSTL,ENC-LIWP - LINEAR P/N:
229150 A - INK:
BLA
CK - MA
TERIAL:
20 LB
. MEAD BOND - SIZE:
11.000”
X 8.500”
- SCALE:
1-1
Copyright © 2009 Linear LLC 229150 A
INSTALL A SINGLE-GANG
OR MULTI-GANG JUNCTION
BOX AT A GOOD LOCATION
FOR THE AUDIO CONNECTION
TO THE SOURCE COMPONENT
ALSO BE SURE THAT THE CABLE
FROM THE KEYPAD CAN BE
EASILY ROUTED TO THE
JUNCTION BOX
Audio In
L R
1
2
Coax In
Optical In
Analog Optical Coax
IR Out
Clip
LOCAL INPUT
WALL PLATE
ANALOG AUDIO INPUTS #1 & #2
LEFT AND RIGHT COLOR CODED "RCA" TYPE JACKS
FOR LINE-LEVEL ANALOG AUDIO OUTPUT FROM THE
AUDIO SOURCE COMPONENT.
INPUT #1 AUTOMATICALLY
OVERRIDES ANY OF THE OTHER INPUTS WHEN AUDIO
IS DETECTED ON INPUT #1.
CLIPPING INDICATOR
LIGHTS IF THE AUDIO INPUT
SIGNAL LEVEL IS TOO HIGH
OPTICAL DIGITAL AUDIO INPUT
"SPDIF" TYPE CONNECTOR FOR FIBER OPTIC
CABLE CONNECTION TO THE AUDIO OUTPUT
FROM THE AUDIO SOURCE COMPONENT
COAXIAL DIGITAL AUDIO INPUT
"RCA" TYPE CONNECTOR FOR COAX
CABLE CONNECTION TO THE DIGITAL AUDIO
OUTPUT FROM THE AUDIO SOURCE COMPONENT
INPUT SELECTOR SWITCH
SET THE SWITCH TO MATCH THE TYPE OF INPUT
USED, ANALOG #2, OPTICAL, OR COAX
INFRARED (IR) OUTPUT JACK
PLUG IR EMITTER INTO THIS JACK AND AFFIX THE EMITTER
TO THE FACEPLATE OF THE SOURCE COMPONENT TO ALLOW
REMOTE CONTROL OF COMPONENT FROM REMOTE KEYPADS
WALL PLATE
J-BOX
CAT-5 CABLE
TO KEYPAD
MAXIMUM WIRE RUN:
300 FEET OF CAT-5 CABLE
FROM KEYPAD TO ANY
LOCAL INPUT WALL PLATE
ONE LOCAL INPUT WALL PLATE
CAN BE USED WITH EACH KEYPAD BLUE POST
ORANGE POST
BROWN POST
GREEN POST
BLU
E S
TR
IPE
BLU
E S
OLID
OR
AN
GE
ST
RIP
E
OR
AN
GE
SO
LID
GR
EE
N S
TR
IPE
GR
EE
N S
OLID
BR
OW
N S
TR
IPE
BR
OW
N S
OLID
110 PUNCH DOWN
STANDARD FOR
CAT-5 CABLE
WIRE ALL 110 PUNCH DOWN
CONNECTORS THIS WAY
PUNCH DOWN CAT-5
CABLE FROM LOCAL
INPUT WALL PLATE
TO KEYPAD "LOC"
CONNECTOR
TO HUB
TO LOCAL INPUT WALL PLATE
ENC-DRS
KEYPAD
INSTALL LOCAL INPUT
WALL PLATE INTO THE
J-BOX AND SECURE IT
WITH THE TWO MOUNTING
SCREWS
INSTALL COVER PLATE
Analog
Optical
Coax
Analog
Optical
Coax
Analog
Optical
Coax
ANALOG STEREO
AUDIO SOURCE
COAX DIGITAL
AUDIO SOURCE
OPTICAL DIGITAL
AUDIO SOURCE
ANALOG
INPUT #1
(OVERRIDE)
ANALOG
INPUT #2
SELECTOR SWITCH
AFTER THE INSTALLATION IS COMPLETE, APPLY POWER
TO THE SYSTEM AND USE THE SOURCE BUTTON TO
SELECT THE LOCAL SOURCE FROM THE KEYPAD
(SOURCE INDICATOR "L" WILL BE LIT)
BE SURE THE LOCAL SOURCE IS PLAYING AUDIO AND
VERIFY THAT THE KEYPAD PLAYS THE AUDIO THROUGH
THE ZONE'S SPEAKERS
SOURCE BUTTON
GAIN SWITCHES
SWITCHES 1-2
ADD GAIN FOR
THE RIGHT CHANNEL
SWITCHES 3-4
ADD GAIN FOR
THE LEFT CHANNEL
GAIN CAN BE ADDED
FOR LOW LEVEL SIGNALS
FOR INPUT #1 AND #2
INPUT 1
INPUT 2
CONNECT CAT-5 CABLE
FROM KEYPAD
TO LOCAL INPUT
WALL PLATE
GAIN
SWITCH #
RIGHT CHANNEL LEFT CHANNEL
1 2 3 4
RIGHT +0db OFF OFF
RIGHT +4db ON OFF
RIGHT +8db OFF ON
RIGHT +10db ON ON
LEFT +0db OFF OFF
LEFT +4db ON OFF
LEFT +8db OFF ON
LEFT +10db ON ON