Echo MS-30H - Manual

Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or
other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized
sprayer in the hot sun. Heat can cause pressure build-up. Do not store or leave solution in tank after use. Always
wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to
remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when pumping or
loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never pres-
surize sprayer by any means other than the original pump. Do not attempt to modify or repair this product ex-
cept with original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas producing
chemicals. Always read and follow manufacturer’s instructions before filling this sprayer as some chemicals
may be hazardous when used with this sprayer.
WARNING!
Parts, Piezas, Pièces
99944100484
Flat Fan Nozzle
Tobera
Buse
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-5387
2. Assembly of Shut-off, Extension Wand and Nozzle
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension wand into shut-off assembly as shown and tighten retaining
nut securely.
3. Filter
The filter helps prevent clogging while spraying. It is located on the end of
the white tube inside your sprayer tank.To clean filter, remove the hose from
the tank and lift out the outlet tube. Make sure the filter is positioned at the
bottom of the tank as pictured.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs
of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
4. Pre-Use Check
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6. Pressurizing and Spraying
7. To Release Pressure
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
WARNING: Handling the brass parts of this product
will expose you to lead, a chemical known to the State
of California to cause birth defects and other reproduc-
tive harm. Wash hands after handling.
011296 (A) R0910
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Filter
Turn handle clockwise to
tighten. Push handle down,
turn1/4 turn counterclock-
wise to release.
Pump until you feel
resistance.
Push handle, down, turn 1/4 turn clockwise
to lock. Begin spraying. Re-pump sprayer as
required to maintain spray force.
For safety lock-off feature (no-spraying), pull up on handle and move red locking mechanism into lock-off position as
shown in fig. 9a. To disengage, push down on handle and return red locking mechanism to neutral position as in fig. 9c.
For lock-on feature (continuous spraying), push down on handle and move red locking mechanism into lock-on position
as shown in fig. 9b. To disengage, push down on handle and return red locking mechanism to neutral position as shown in
fig. 9c.
9. Fatigue-free spraying
Your sprayer is equipped with a pressure relief release valve. To release pressure lift
and hold the cap until air is completely exhausted, OR, turn the valve slowly coun-
terclockwise until you hear air escaping and wait until air is completely exhausted.
Nozzle Assembly
Figure 1-2
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the
retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle,
reverse the above instructions.
Figure 3
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the
nozzle, reverse the above instructions.
99944100483
Poly Adjustable Nozzle
Tobera
Buse
99944100482
Brass Adjustable Nozzle
Tobera
Buse
99944100485
Nozzle Kit
Tobera
Buse
9a 9b 9c
Shut-off Assembly
Retaining Nut
Extension Wand
Nozzle Assembly
99944100479
Hose Assembly
Ensamblaje de la manguera
Assemblage de boyau
Retaining Nut
Filter
99944100486
Wand O-ring Kit
Kit del anillo “O”
Trousse de joint torique
Elbow O-ring Hose Washer
Nozzle Gasket Wand O-ring
3a
2a
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
www.echo-usa.com
7a
Model# MS-20H Model# MS-30H
1. Hose to Tank
If the handle fails to operate correctly, release the pressure from the tank by turning the pressure release knob on the
tank . Inspect and repair the handle assembly or replace with a new handle assembly.
99944100477
Shut-offf Valve Repair Kit
Kit de reparación para la válvula
de cierre.
Trousse de réparation de robinet
d’arrêt.
99944100487
Repair Kit
Juego de reparación
Kit de réparation
“C” Clip
Clip de “C”
Clip de « C »
99944100478
Shut-off Assembly
Unidad de cierre
Assemblage d’arrêt
99944100480
Extension wand, Vara de extensión, Lance de rallonge
Make sure white outlet
tube is attached to hose.
Insert tube into
tank.
1A 1B
Proper placement of
white outlet tube.
1C
Line up tabs on safety lock
connector with notches on
the outlet flange of the tank.
Insert tabs into notches to
form a secure seal.
4
1D
Slip hose nut down to tank,
turnclockwise and tighten as
tight as possible by hand.
1E
6a 6b 6c