ShoreLand'r DK2146TB - Manual

®
DK2146T B, DK2346T B & DK2446T B
Bundles Required
DK2146T B Deck Boat Trailer, 4600 lbs.
4 4300215 ST185/80R 13-C Tire/Galv. Dir Rim (or)
4 4300218 ST185/80R 13-C Tire/MSilver Dir Rim
1 62340 Literature Bag - Trailers
1 62300-- Frame Bundle - DK2146T B
1 6238600 Rocker Arm Bag
1 T-1310 Axle, 78-3/8”
1 T-1310B Axle W/Brakes
Tire Size &
Carrying Capacity Chart
Tire Load Carrying
Size Range Capacity
ST185/80R13 C 1480 lbs. per tire
Refer to tire side wall for correct tire pressure.
Tongue Weight Adjustment
Approximate Tongue Weight for Best Towing.
Tongue weight too high, move the axle assembly forward. Tongue
weight too low, move the axle assembly backward. Tongue weight
should be 5% to 7% of the total gross weight of the boat and
trailer combined.
Final Assembly Instructions for the DK2146T B, DK2346T B & DK2446T B
DK2346T B Deck Boat Trailer, 4600 lbs.
4 4300215 ST185/80R 13-C Tire/Galv. Dir Rim (or)
4 4300218 ST185/80R 13-C Tire/MSilver Dir Rim
1 62340 Literature Bag - Trailers
1 62772-- Frame Bundle - DK2346T B
1 6238600 Rocker Arm Bag
1 T-1310 Axle, 78-3/8”
1 T-1310B Axle W/Brakes
DK2446T B Deck Boat Trailer, 4600 lbs.
4 4300215 ST185/80R 13-C Tire/Galv. Dir Rim (or)
4 4300218 ST185/80R 13-C Tire/MSilver Dir Rim
1 62340 Literature Bag - Trailers
1 62302-- Frame Bundle - DK2446T B
1 6238600 Rocker Arm Bag
1 T-1310 Axle, 78-3/8”
1 T-1310B Axle W/Brakes
Remove the small parts from the frame by cutting the bands.
Remove the bolt bag and sort all nuts and bolts by size.
Rocker Boxes:
Align the center hole of 6239210, rocker arm, with the center hole
of spring bracket. Secure with a 3/4” X 4-1/2” hex bolt from
outside-in and tighten with a 3/4” hex lock nut. Repeat on the
other side of the trailer.
Axles:
Fasten the springs to the axles with the 1/2” X 6-1/2” axle u-bolts,
spring plate (Ref.#121) and 1/2” flange lock nuts. NOTE: Make
certain the hook end of the springs point in the same direction - to
the rear of the trailer - on both axles! For the rear spring and axle
assembly - place a S-3207 - galvanized spring bracket bushing
(Ref.#118) in the rear of the spring bracket. Insert a 9/16” X 3-1/4”
hex bolt through the bracket from the outside in and tightened with
a 9/16” hex lock nut. Slide the end of the hook spring over the
bushing; raise the front of the spring and fasten with a 9/16” X 3-1/
4” hex bolt and 9/16” hex lock nut.
For installation of the front spring and axle assembly repeat the
above procedure, however, place the bushing in the rocker box in
the hook end of the spring. Insert the bolts and secure with lock
nuts as before.
Mount the tire and rim assemblies using 80-90 ft. lbs. torque on
the lug nuts.
Tongue:
Slip the tongue into the front frame cap of the frame. Line up the
holes; fasten the tongue in the frame with a 1/2” X 4-1/4” hex bolt
and 1/2” flange lock nut at the front of the frame cap; fasten the
tongue in the rear of the frame cap with a 1/2” X 1-1/2” hex bolt
and 1/2” lock nut at the rear of the frame cap. Pull the wire
harness through the hole in the top of the tongue, then backward
out of the tongue. Place rubber grommet in the hole. Plug the
tongue harness into the frame harness.
Actuator & Safety Chain:
Slide the actuator (Ref.#138) into the actuator housing unit
(Ref.#137) and secure with two (pins) and snap rings provided
with the actuator. Secure the actuator-housing unit to the front of
the tongue using three (3) 1/2” X 4” hex bolts and 1/2” flat washer
on 1/2” X 5” hex bolt on the lower right mounting hole on the
tongue, secure the safety chain. Place a 1/2” flat washer on the 1/
2” X 5” hex bolt followed by one (1) safety chain and insert into the
actuator housing unit and the tongue. Place the second safety
chain on the bolt followed by a 1/2” flat washer and 1/2” flange
lock nut. Tighten.
Brakes:
Refer to the brake manual for service and maintenance.
Continue to page 4...