ShoreLand'r PWC1512W - Manual

PWC1512W & PWC1810W Parts Manual
PWC1512W PWC 1500# Trailer; White
2 4300184 5.30 X 12-C Tire/MSilver Mod. Rim
1 62340 Literature Bag - Trailers
1 6408201 Frame Bundle - PWC 2-Place - White
1 6408501 PWC Walkboard W/Carpet
1 6432403 Axle Assembly - Black
PWCG1512W PWC 1500# Trailer; Galvanized
2 4300206 5.30 X 12-C Tire/Galv. Mod. Rim
1 62340 Literature Bag - Trailers
1 6408200 Frame Bundle - PWC 2-Place - Galv.
1 6408500 PWC Walkboard W/Carpet
1 6432400 Axle Assembly - Galvanized
PWCBK1512W PWC 1500# Trailer; Black
2 4300184 5.30 X 12-C Tire/MSilver Mod. Rim
1 62340 Literature Bag - Trailers
1 6408203 Frame Bundle - PWC 2-Place - Black
1 6408503 PWC Walkboard W/Carpet
1 6432403 Axle Assembly - Black
PWC1810W PWC 1800# Trailer; White
2 4300181 20.5 X 8 X 10D Tire/MSilver Rim
1 62340 Literature Bag - Trailers
1 6408201 Frame Bundle - PWC 2-Place - White
1 6408501 PWC Walkboard W/Carpet
1 6432403 Axle Assembly - Black
PWCG1810W PWC 1800# Trailer; Galvanized
2 4300203 20.5 X 8 X 10D Tire/Galv. Rim
1 62340 Literature Bag - Trailers
1 6408200 Frame Bundle - PWC 2-Place - Galv.
1 6408500 PWC Walkboard W/Carpet
1 6432400 Axle Assembly - Galvanized
PWCBK1810W PWC 1800# Trailer; Black
2 4300181 20.5 X 8 X 10D Tire/MSilver Rim
1 62340 Literature Bag - Trailers
1 6408203 Frame Bundle - PWC 2-Place - Black
1 6408503 PWC Walkboard W/Carpet
1 6432403 Axle Assembly - Black
Tire Size &
Carrying Capacity Chart
Tire Load Carrying
Size Range Capacity
5.30 X 12 C 1045 lbs. p/tire
20.5 X 8 X 10 D 1330 lbs. p/tire
Refer to tire side wall for correct tire pressure.
Tongue Weight Adjustment
Approximate Tongue Weight for Best Towing.
Tongue weight too high, move the axle assembly forward. Tongue
weight too low, move the axle assembly backward. Tongue weight
should be 5% to 7% of the total gross weight of the boat and
trailer combined.
Final Assembly Instructions for the PWC2013W
Winch:
Mount the winch post weldment (Ref.#49) to the winch
mounting channels on the frame. The winch post weldment can be
adjusted to the winch mounting channels to best fit your particular
water vehicle. Also notice the winch post weldment is also
adjustable. When the desired position has been determined secure
the winch post weldment to the winch mounting channel with two
(2) 3/8” X 3-3/4” hex bolts and two (2) 3/8” flange lock nuts.
Axle:
Install the spring bushings (Ref.#1) in the rear of the spring
brackets with 9/16” X 3-1/4” hex bolts and 9/16” flange lock nuts.
Position the axle under the trailer with spring eye to the front.Slip
the spring in the rear of the spring bracket and fasten the front
spring eye to the front spring bracket with 1/2” X 3-1/4” hex bolts
and 1/2” flange lock nuts.
Mount the tire and rim assemblies with 1/2” lug nuts and tighten
to 80-90 ft./lbs. of torque.
Walk Board:
Mount the front walk board bracket (Ref.#75) to the front of the
frame using two (2) 3/8” X 5” carriage bolts and secure with 3/8”
lock washers and 3/8” hex nuts. Mount the back walk board plates
(Ref.#76) to the middle and rear crossmembers using 3/8” X 3-1/2”
carriage bolts and securing with 3/8” flange lock nuts. Mount the
walk board (Ref.#50) to all three (3) walk board mounting brackets
just installed using six (6) #10 X 1-1/2” ph pts screws (Ref.#18).
NOTE: Mount the walk board to the brackets with the six (6)
screws from the underside of the trailer up through the walk board.
Bunks:
Slide the 3/8” X 3-7/16” X 3” square u-bolts (Ref.#15) over the
rear crossmember with the threads of the square u-bolt’s facing out
the rear of the trailer. Place the adjustment bunk brackets
(Ref.#72) on the square u-bolt and secure with 3/8” lock washers
and 3/8” hex nuts. Place the bunk assemblies on top of the
adjustable bunk brackets just installed. Secure the bunk assem-
blies using a 3/8” X 1” hex bolts and 3/8” flange lock nuts.
Secure the opposite end of the bunk assemblies to the front
crossmember by sliding a 3/8” X 3-7/16” X 3”square u-bolt’s
(Ref.#15) over the threads of the square u-bolt’s facing the front of
the trailer. Secure with 3/8” lock washers and 3/8” hex nuts. Place
the adjustable bunk bracket (Ref.#72) over the top of the adjust-
able bunk bracket just installed and secure with 3/8” X 1” hex bolts
and 3/8” flange lock nuts. Repeat the previous steps to mount the
remaining bunks.
NOTE: The tie-down brackets on bunks must be positioned at
the rear of the trailer.