ShoreLand'r LUXR2314SW V.1 - Manual (Page 3)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003809
Page 3 REV B 02/05/2009
ShoreLand’r offers their product line in either galvanized or paint-
ed finish. When ordering parts it is important that you specify the
finish or color you have on your product. The five (5) digit number
along with a two (2) digit space _ _, note the parts which can be
purchased with various finishes. When ordering these items use
the five (5) digit number along with a two (2) digit suffix for the
proper finish.
01.........White
03.........Black
14 ......... Blue
22 ......... Red
24 ......... Majestic Red
39 ......... Galvanized w/Silver Plastic Components
LUXR2314SW (All Colors) Specifications:
Capacity: 2300 lbs.
GVWR: 2995 lbs.
GAWR: 2995 lbs.
Ship Wt: 575 lbs.
Frm Size: 2X4 (11 Ga)
Tire Size: ST215/75R14-C
Rim Size: 14 X 6 “J”
Brake: N/A
Coupler: 2”
Safety Chn: 7600 lb.
Suspension: 5 Leaf Hook Springs
Tongue Size: 3 X 5 X 65” Swing Tongue
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove parts and sort
by size. Remove all the banded items from the frame.
TONGUE
Install the swing tongue by sliding it in the front of the tongue chan-
nel. Line the holes in the tongue with the holes in the tongue chan-
nel. Install the 1/2” x 4” hex bolt in the front cross hole and secure
with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue. Place it
through the hole provided in the tongue cover plate.
Secure the tongue cover plate in position with the same 1/2” x 1-
1/2” hex bolt that secures the back of the tongue to the tongue
channel of the frame. Secure with a 1/2” lock nut. Tighten both bolts
just installed.
Plug the tongue wire harness into the frame harnesses by match-
ing colors and ends. Push the extra wire provided either into the
rear of the tongue or else remove the grommets in the side frame
and place the extra wire in the side frame. Replace grommets just
removed.
SAFETY CHAINS
Locate a 3/8” x1 1/4” hex bolt. Slip the bolt through a 3/8” flat wash-
er, then place through the last link of one of the safety chains.
Place the bolt with chain attached through the hole provided in the
bottom front of the tongue. Secure with a 3/8” flange lock nut. Tight-
en. Repeat on the other side and safety chain.
RETRACTABLE TIE DOWNS
Locate the two retractable tie downs. Next locate one of the 7/16”
x 1 ½” fine threaded bolts supplied with the retractable tie down.
Insert it into the bottom hole on the retractable tie down so the bolt
is pointing through the back side of the tie down. Insert the bolt
through the hole provided in the taillight bracket just inside the side
frame. Secure with the 7/16” flange lock nut. Tighten.
Repeat the above process on the other tie down.
WINCH POST ASSEMBLY
Your trailer may have come with the jack already installed on the
winch base. However, in the event that it did not, use the following
instructions to attach the jack to the winch base before it is installed
on the tongue.
ASSEMBLY AND MOUNTING INSTRUCTIONS:
JACK ON A PROFILE 2000 WINCH BASE
The Profile 2000 winch base used on the 2” x 4” and 2” x 5” frame
trailers is formed so that the jack can be mounted directly to it elimi-