ShoreLand'r LUXR30BSW V.1 - Manual (Page 12)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003683
Page 12 REV C 02/09/2009
TRAILER ADJUSTMENTS
The adjustment of the trailer to your boat is very important not only
for the trailer, but also the boat. Failure to do so may lead to poten-
tial failure or damage to either the trailer or boat.
Adjust as follows:
Axle Adjustment
The amount of tongue weight on your trailer can be adjusted as
follows:
To lower the tongue weight, adjust the axle assembly forward. To
in¬crease the tongue weight, adjust the axle backward.
The distance that the axle assembly has to be moved will vary be-
cause it is directly related to the weight and center of gravity of the
boat placed on it.
Best towing is achieved when the tongue weight is 5-7% of the total
gross load of the complete unit.
Wire harnesses and brake line lines will need care when moving
the axle assembly.
Rear Support System
Place the boat on the trailer so that the transom is located at the
rear of the support system. The transom of the boat should be 4” to
the center of the rear roller.
Position the roller racks so they are far enough apart to give
your boat stability while transporting. When the desired width is
achieved, move the roller rack system so that the rollers are just to
the outside of a strake. The rollers need to be adjusted so that you
have a minimum of one to two inches of clearance between the
keel of the boat and the center cross member pad. This will help
center the boat when loading and unloading.
When the desired position is determined, tighten only enough to
hold the rollers from moving while the other adjustments are be-
ing made. Final tightening will be done at the end of the adjusting
process.
Front Support System
The front roller assemblies on the XR series will need to be adjusted
to fit your boat. Place the roller assemblies so that the outside set
of rollers is just to the outside of a strake if your boat has strakes.
This is a desired location if the front of the boat isn’t setting to high
on the trailer with respect to the frame. Positioned as described will
help with centering your boat. If there are no strakes the roller as-
semblies can be positioned anywhere.
As a rule, when the XR roller arm assemblies are moved away from
the centerline of the trailer the front of the boat will be lowered with
respect to the trailer frame. The rollers should be moved outward
until the keel of the boat is within 1-2 inches of the front cross mem-
ber pad. The boat should be kept as low as possible on the trailer
for better towing but must also be positioned so that the front of the
boat is either level or slightly higher in front that the rear. The boat
will unload easier if the front of the boat is slightly higher than the
rear.
Most boats can be adapted to the trailer without the need of rais-
ing the XR arms higher than the way they are shipped. However,
if need be, they can be raised higher with the use of an optional
SS1000 riser kit.
Winch Post
The winch post is pre-adjusted to fit the boat. If it does not, use the
following instructions to adjust to properly fit your boat.
Once all other adjustments are complete the winch post can be ad-
justed. Slide the winch post base backward on the tongue until the
bow roller comes in contact with the boat. This bow roller needs to
be positioned directly above the boat bow eye to prevent your boat
from moving forward in the event of a sudden stop. It can be moved
up or down by removing the back bolt that mounts the winch head
to the base. When this bolt is removed, the head can be rotated up
or down to reach the desired height required to fit your boat. Once
in this position, align the closest pair of holes in the brackets and
reinsert the bolt just removed. Tighten. Attach the winch strap and
crank winch tight. Attach the bow eye safety chain into the bow eye
of the boat as well. This is just another level of protection to keep
your boat and trailer together as one unit.
Check the boat to make sure it is in the desired location forward
and backward on the trailer. If location is as instructed above, tight-
en the three bolts in the winch base securing the winch base to the
tongue.
Once all adjustments are complete and checked, connect to the
tow vehicle to make sure all of the lights are operating properly and
match the tow vehicle.
Re-check all fasteners on the complete trailer to make sure they
are all tight and ready for towing. All fasteners should be periodi-
cally check before towing.
See your ShoreLand’r Owner’s Guide for further technical infor-
mation regarding your trailer and its components.