Yaskawa P7 Drive User Manual - Manual (Page 247)

Index - 7
Maximum Boost Time .....................................5-22, A-7
Offset Adjustment ........................................... 5-17, A-6
Output ......................................................................5-17
Gain Setting ..............................................5-18, A-6
Level Selection..........................................5-17, A-6
Limit..........................................................5-17, A-6
Square Root Monitor.................................5-23, A-7
Parameters ...................................5-15 to 5-23, A-5, A-7
Primary Delay Time Constant...................................A-6
Setpoint ...........................................................5-15, A-7
Boost Setting .............................................5-21, A-7
Display Scaling .........................................5-20, A-7
Selection....................................................5-19, A-7
Value .........................................................5-20, A-7
Sleep
Delay Time................................................5-19, A-7
Function ............................................................5-19
Function Start Level..................................5-19, A-7
Input Source ..............................................5-21, A-7
Snooze
Deactivation Level ....................................5-12, A-7
Delay Time................................................5-21, A-7
Feedback Level .........................................5-22, A-7
Function ............................................................5-21
Level .........................................................5-21, A-7
Square Root Gain .............................................5-23, A-7
PI Mode ...................................................................5-15, A-6
PI Monitors
Feedback (U1-24)...........................................5-20, A-26
Output (U1-37)...............................................5-19, A-26
Setpoint (U1-38).............................................5-20, A-26
PLC (Programmable Logic Controller)
Serial Com. Using Modbus Protocol ........................D-2
Troubleshooting .......................................................6-17
Power
Detection Filter Time ................................................A-7
Energy Saving ..........................................................5-24
Output, +15Vdc.............................................. 2-23, 2-27
Loss Ride-thru .......................................5-39, A-19, C-4
PCB
Inspecting ............................................................7-2
Supply Specifications........................................ C-2, C-3
Power Factor Correction Capacitors .................................6-6
Pre-Operation Considerations ................... i to iv; Ch. 1, 2, 4
Preset Speeds....................................................................A-9
Preventive Maintenance ....................................................7-3
Programming
Basic.............................................................. 5-1 to 5-60
Error (OPE) .............................................................. 6-11
Menu ............................................................. 3-6 to 3-15
Proportional Gain (PI)..............................................A-6
Protective
Functions ...................................................................C-4
Structure.....................................................................C-4
PWM Frequency — See Carrier Frequency .................... A-9
Q
Quick Setting Menu ........................................................ 3-11
R
RAM .............................................................................. D-12
Ramp to Stop .................................................................... 5-6
Rated Current, Motor....................4-6, 5-31, 6-12, A-11, B-4
Rdy.................................................................................... 3-2
Reactors, Preventive Maintenance.................................... 7-3
READ.............................................................................. 5-56
Ready Display................................................................... 3-2
Receiving ......................................................................... 1-3
REF Indicator ............................................................ 3-2, 3-4
Reference Limits
(Also see Frequency) ..........5-26, 6-19, A-9
Reference Source ...................................................... 5-4, A-4
Relays, Preventive Maintenance....................................... 7-3
REMOTE
Key............................................................................. 3-3
Mode .......................................................................... 3-3
REF Indicator ..................................................... 3-2, 3-4
SEQ Indicator .................................................... 3-2, 3-4
Also see Spare Parts Ordering ...........Inside Back Cover
RESET Key ...................................................................... 3-3
Resistance, Motor Line-to-Line .....................................A-11
Resonance ....................................................................... 5-27
REV Indicator ................................................................. 3-4
Reverse Operation..................................................... 5-8, A-4
Prohibiting ................................................5-8, 6-16, A-4
Reverse Run/Stop command.................................. 2-23, 2-27
Ride-thru, Momentary Power Loss......5-11, 5-39, A-19, C-4
"Right Arrow" Key ........................................................... 3-3
RS-485/422 ...................................................................... 5-5
Communication Wiring ............................................ D-3
Control Circuit Terminals ........................................ 2-23
Parameters ..............................................5-4, 5-32, A-18
Terminating Resistance.................................... 2-24, D-3
RTS Control Selection ................................................... A-18
Run Command
During Program ................................................. 5-8, A-4
External, Troubleshooting ....................................... 6-15
Selection ............................................. 3-4, 4-6, 5-4, A-4
Source ........................................................................ 5-4