Extron Electronics P-2 DA2 WM_EC and AAP - Manual (Page 7)

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation
“Euro Channel installation” section.
6 Power up all of the input and output devices.
7 The image should now display on screen. If it does
not, double check steps 3 through 6 and make
adjustments as needed. Refer to the section “Setting
the DIP switches” in this chapter.
8 For the P/2 DA2 WM, attach the P/2 DA2 WM to the
wall mounting bracket (see “P/2 DA2 WM wall
installation”).
For the P/2 DA2 EC, attach the P/2 DA2 EC to the
Euro Channel (see “P/2 DA2 EC Euro Channel
installation”).
Installing the mounting bracket
The wall-mounted P/2 DA2 WM kit includes a mounting
bracket which is installed in a wall opening. The AAP
version of the P/2 DA2 WM uses a wider mounting
bracket, as shown below.
1. Once the proper wall location for mounting the
distribution amplifier has been selected, cut an
opening in the wall using the proper mounting
template found in the “Appendix” section.
2. Using two supplied screws and mounting clips,
attach the mounting bracket to the hole opening, as
shown below.
Figure 2-4 — Installing the mounting bracket
2-5
wall mounting bracket wall mounting bracket
for Architectural Adapter Plate
Detail A
0.75" #6-32 Screw
Backing Clip Backing Clip
Sheet Rock
Sheet Rock
Mounting Bracket
Mounting Bracket
Mounting Bracket
Detail B
1.25" #6-32 Screw
Backing Clip can
be in either orientation.
See Detail A or Detail B.
Mounting Bracket
Backing Clip can
be in either orientation.
See Detail A or Detail B.
Installing the P/2 DA2 WM/EC
Easy setup procedure
The wall-mounted P/2 DA2 WM kit consists of the
faceplate/distribution amplifier assembly and a mounting
bracket which mounts in a wall opening and to which the
faceplate assembly is attached. The P/2 DA2 EC kit
consists of the faceplate/distribution amplifier assembly
which mounts in the Euro Channel raceway.
1 For wall mounting only: Using the mounting
template provided in the “Appendix” as a guide,
carefully cut a mounting hole through the wall where
the mounting bracket is to be installed.
2 For wall mounting only: Install the mounting bracket
using the supplied screws and mounting clips. Refer
to the section “Installing the mounting bracket” for
further details.
3 Before connecting any cables, power off all
equipment. If the optional Architectural Adapter
Plate (AAP) is being installed, please refer to
“Installing Architectural Adapter Plates” in this chapter.
4 The rear connectors are the same for both WM and
EC models. Please refer to figure 2-3. Connect the
VGA output cable to the 15-pin HD female output
connector. To prevent installation debris or objects
from entering the opening in the sheet metal just
above this VGA connector, it is suggested that some
masking tape be used to temporarily cover this
opening. Remove this tape after installation is
completed. Next, if there is audio output, connect
the audio output cable to the 3.5 mm captive screw
connector. Finally, connect the power cable to the
power input connector. Refer to the “Cabling” and
“Connecting audio” sections of this chapter.
5 Before attaching the faceplate assembly to the wall
mounting bracket/Euro Channel, attach the
computer video cable to the 15-pin HD female input
connector on the faceplate. Next, a local monitor
may be connected to the 15-pin HD female buffered
local monitor output connector on the faceplate.
Finally, for audio input, connect the audio cable to
the faceplate’s 3.5 mm audio input jack. Refer to the
“Cabling” and “Connecting audio” sections of this
chapter. For Euro Channel applications, refer to the
2-4
Controls and Installation, cont’d