Kichler 43686 - Manual

IMPORTANT SAFETY INSTRUCTIONS
LIGHTED BULB IS HOT!
WARNING: To reduce the risk of FIRE or INJURY TO PERSON:
• Turn off and allow to cool before replacing bulb.
• Bulb gets HOT QUICKLY! Contact switch only when turning off.
• DO NOT remain in light if skin feels warm. (Light is intense,
may cause “sunburn”)
• DO NOT look directly at lighted bulb.
• Keep materials away from bulb that may burn.
• Use ONLY with wattage specified or lower.
• DO NOT touch bulb at any time, use a soft cloth. Oil from skin
may damage bulb.
• DO NOT operate fixture with missing or damaged glass.
1) Pass fixture wire from each coupling on top of fixture
through one stem for each side and screw each stem into
each coupling. NOTE: Thread locking compound must be
applied to all stem threads as noted with symbol (3) to
prevent accidental rotation of fixture during cleaning,
relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire through first loop. Thread one first loop
onto end of each last stem.
5) Pass fixture wire through second loop and through hole in
canopy. Pass threaded pipe at end of second loop through
hole in canopy.
6) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
7) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
8) Repeat steps 5-7 to attach last stem to canopy.
9) Attach chain link to small loop at end of each stem and to
each loop on canopy.
10) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
11) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
12) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
13) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
Date Issued: 10/17/14 IS-43686-US
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
SMALL LOOP
ARGOLLA
PEQUEÑA
CHAIN LINK
ESLABÓN DE CADENA
STEM
VASTAGO
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
GLASS
VIDRIO
14) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
15) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
16) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
17) Raise glass up to fixture. Pass top of glass through hole in
bottom of fixture body. Pass hole in glass over socket.
18) Slip spacer over socket.
19) Attach socket ring to socket ring tool.
20) Raise socket ring tool with socket ring attached up to fixture
Pass socket ring tool with socket ring attached through hole in
glass. Thread socket ring onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
21) Insert recommended bulb. CAUTION: DO NOT touch bulb
with bare hands. If this happens, clean bulb with denatured
alcohol and a lint free cloth.
22) Slip glass sleeve over bulb. Carefully thread glass sleeve
onto socket. (DO NOT over tighten.)
HEXNUT
TUERCA
HEXAGONAL
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
LOCKWASHER
ARANDELA DE
SEGURIDAD
3
3
3
SOCKET RING
ANILLO DEL CASQUILLO
SPACER
ESPACIADOR
SOCKET RING TOOL
HERRAMIENTA DEL
ANILLO DEL CASQUILLO
FIXTURE BODY
CUERPO DEL ARTEFACTO
BULB
BOMBILLA
GLASS SLEEVE
CAMISA DE VIDRIO