Kichler 43360 User Manual

We’re here to help

Advertising

MOUNTING STRAP

ABRAZADERA DE MONTAJE

1) Adjust the length of the cables to achieve the desired height

of the mounted fixture. (See cable adjustment detail)

To raise fixture: Push cable up into canopy. Release cable

and cable will lock into place.

To lower fixture: Push button in on cable adjuster and pull

cable down. Release button to lock cable in place.

NOTE: With button pushed in cable will raise and lower.

Without button pushed in cable will only raise up and lock in

place.
2) Slip center cord from fixture through hole in short tube on

center of canopy. Match length of center cord with length of

cables. Thread set screw through hole on side of center

tube. Tighten set screw to secure center cord.

3) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the fixture or room

that you are working on.

c) Place the wall switch in the “OFF” position. If the fixture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

4) Find the appropriate threaded holes on mounting strap.

Assemble mounting screws into threaded holes.

5) Attach mounting strap to outlet box. (Screws provided).

Mounting strap can be adjusted to suit position of fixture.

6) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a

hole and two raised dimples. Wrap ground wire from

outlet box around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Attach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounting strap.

If fixture is provided with ground wire. Connect fixture

ground wire to outlet box ground wire with wire connector.

(Not provided.) After following the above steps. Never

connect ground wire to black or white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOT PROVIDED)

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black

White

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)

Neutral Wire

Date Issued: 9/27/13

IS-43360-US

CANOPY

ESCUDETE

KNURL KNOB

PERILLA ESTRADA

THREADED PIPE

TUBO ROSCADO

BOTTOM TRIM

GUARNICIÓN INFERIOR

FINIAL

CAPUCHON

HEXNUT

TUERCA HEXAGONAL

RUBBER WASHER

ARANDELA DE CAUCHO

FLAT WASHER

ARANDELA PLANA

DIFFUSER

DIFUSOR

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

SHADE

PANTALLA

CAGE

JAULA

7) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

8) Push fixture to ceiling, carefully passing mounting screws

through holes in canopy.

9) Thread knurl knobs onto mounting screws. Tighten knurl

knobs to secure fixture to ceiling.

10) Raise shade up to fixture. Fit shade inside cage on fixture.

Align holes in bracket on shade with holes in bracket on

inside of cage.

11) From inside shade, thread ball studs up through holes in

bracket and into holes in cage. Tighten ball studs to secure

shade in place.

12) Insert recommended bulbs.
13) Thread end of threaded pipe with hexnut into coupling in

center of socket cluster.

14) Slip flat washer then rubber washer over end of threaded pipe.
15) Raise diffuser up to fixture. Pass holes in diffuser over end

of threaded pipe.

16) Thread hexnut onto end of threaded pipe. Tighten hexnut to

secure diffuser in place. (DO NOT over tighten.)

17) Pass hole in bottom trim over end of threaded pipe.
18) Thread finial onto end of threaded pipe. (DO NOT over tighten.)
NOTE: Adjust position of the fixture after installation for leveling
purposes of one inch or less. (See cable adjustment detail)

BALL STUD

ESPÁRRAGO DE

CABEZA ESFÉRICA

PRESSED

CABLE ADJUSMENT DETAIL

EL DETALLE DE AJUSTE DEL CABLE

NOT

PRESSED

UP & DOWN

UP ONLY

CABLE

SET SCREW

TORNILLO DE

FIJACIÓN

SHORT TUBE

TUBO CORTO

CENTER CORD

CORDÓN DEL CENTRO