Kichler 42890 - Manual

Date Issued: 11/28/14 IS-42890-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Insert recommended bulbs.
2) Lower cap down to glass. Fit bulb inside glass.
3) Fit one bracket around indentation in glass. Align holes on each end of bracket
with holes at end of each arm on fixture.
4) Fit second bracket around indentation in glass. Align hole on each end of bracket
with holes at end of each arm on fixture and holes in first bracket.
5) Slip end of one ball stud through holes in brackets and arm.
6) Thread ball knob onto end of ball stud protruding from hole in bracket.
7) Repeats steps 5 and 6 for remaining ball stud and ball knob.
8) Tighten both ball knobs to secure brackets in place.
9) Adjust the length of the cords to achieve the desired height of the mounted
fixture.
To adjust cord length: On outside of canopy on each cord is a strain relief.
Unscrew strain relief from plastic threaded pipe on canopy and slide strain relief
down cord a few inches. Pull cord up or down to lengthen or shorten cord. Once
desired height of fixture is achieved, raise the strain relief on the outside of
canopy up the cord and thread strain relief onto plastic threaded pipe. Tighten
strain relief until top of strain relief is flush with canopy.
10) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work without shutting off the
electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s), that control
the power to the fixture or room that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in the “OFF” position.
11) Attach fixture mounting screws to mounting bracket: From the side of the mounting
bracket that will be against the ceiling, thread each fixture mounting screw down
through each fixture mounting fixture screw hole. Thread one hexnut onto each
end of mounting screw protruding from other side of mounting bracket. Tighten
each hexnut up against mounting bracket.
12) At the center of the mounting bracket are knock out slots. Remove the knock slots
that match your outlet box.
13) Place mounting bracket up against ceiling. Pull outlet box wires through center
hole of mounting bracket.
14) Align correct knock out slots in mounting bracket with mounting holes in outlet box.
15) Thread outlet mounting box screws into knockout slots in mounting bracket and
into holes in outlet box. Tighten screws to secure mounting bracket to ceiling.
16) From the inside of the canopy, gather the four cords from the fixtures running in a
row along the front of the canopy into one group in the center of the canopy.
REF: Fixture wiring detail.
17) Gather the four cords from the fixtures running in a row along the back of the
canopy into a second group in the center of the canopy. REF: Fixture wiring detail.
18) For each cord, from the point where the cord meets in the center of canopy,
measure 6" of cord passed that point. Trim each cord. REF: Fixture wiring detail.
19) For each cord, with wire strippers, remove 2 inches from end of each wire jacket.
Then strip 1/2 inch from end of each color wire. REF: Stripped Wires Detail and
Fixture Wiring Detail.
20) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole and two raised
dimples. Wrap ground wire from outlet box around green ground screw, and
thread into hole.
B) On fixtures where a cupped washer is provided. Attach ground wire from
outlet box under cupped washer and green ground screw, and thread into
mounting strap.
If fixture is provided with ground wire. Connect fixture ground wire to outlet box
ground wire with wire connector. (Not provided.) After following the above steps.
Never connect ground wire to black or white power supply wires.
21) Connect each black wire together with one black jumper wire with wire connector.
REF: Fixture wiring detail.
22) Connect each green wire together with one green jumper wire with wire connector.
REF: Fixture wiring detail.
23) Connect each white wire together with one white jumper wire with wire connector.
REF: Fixture wiring detail.
24) Make wire connections from jumper wires to outlet box wires. (Connectors not
provided.) Reference chart below for correct connections and wire accordingly.
25) Push fixture to ceiling, carefully passing mounting screws on mounting bracket
through each hole in canopy. CAUTION: Be careful not to pinch wires between
canopy and ceiling.
26) Screw threaded balls onto mounting screws. Tighten mounting screws to secure
fixture to ceiling.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire To Attach Optional Slide Ring (Not Included):
1) Gather cords together.
2) Place one half of slide ring around cords so cords fit inside curve of slide ring half.
3) Place other half of slide ring around cords on the opposite side of first slide ring
half. Fit cords inside curve of slide ring.
4) Align holes in ends of each half of slide ring.
5) Pass end of one ball stud through one hole in ends of one side of each slide ring.
6) Thread ball knob onto end of ball stud protruding through hole in slide ring.
7) Repeat steps 5 and 6 to attach other side of slide ring.
8) Tighten both ball knobs to secure two halves of slide ring together.
STRIPPED WIRES DETAIL
DETALLE DE LOS ALAMBRES PELADOS
FIXTURE WIRING DETAIL
DETALLE DEL ALAMBRADO DEL ARTEFACTO
WIRE JACKET
REMOVE 2"
CAMISA DE
ALAMBRE
RETIRE 2
PULGADAS
COLORED WIRES
REMOVE
1/2" OF EACH
ALAMBRE DE
COLOR
RETIRE 1/2
PULGADA
DE CADA
6"
6"
FOR EACH COLOR WIRE
PARA CADA ALAMBRE DE COLOR
JUMPER WIRE
ALAMBRE DE
CONEXIÓN
CORD
CORDÓN
MOUNTING
BRACKET
SOPORTE
DE MONTAJE
MOUNTING
SCREW
TORNILLO
DE MONTAJE
THREADED
BALL
ESFERA
ROSCADA
CANOPY
ESCUDETE
CORD
CORDÓN
CAP
TAPA
ARM
BRAZO
BRACKET
MÉNSULA
BALL STUD
PERNO ESFÉRICO BALL KNOB
PERILLA ESFÉRICA
GLASS
VIDRIO
JUMPER WIRE
ALAMBRE DE
CONEXIÓN
CORD
CORDÓN
FOR EACH COLOR WIRE
PARA CADA ALAMBRE
DE COLOR
OPTIONAL SLIDE RING (NOT INCLUDED)
ANILLO DESLIZANTE OPCIONAL (NO INCLUIDO)
SLIDE RING
ANILLO DESLIZANTE
BALL STUD
ESPÁRRAGO DE
CABEZA ESFÉRICA
BALL KNOB
PERILLA REDONDA
SLIDE RING
ANILLO
DESLIZANTE