Crivit Z31335 User Manual

Crivit For bicycles

Advertising

GB/IE

Bike Computer

Proper use

The product is intended for use as a cycle computer.
Not for commercial use.

Functions

– Menu languages: GB, DE, FR, NL, IT, ES
– Clock
– Stopwatch
– Temperature °C / °F
– Memory function for min. and max. temperature
– Current speed (0–99.9 km / h)
– Mean speed (0–99.9 km / h)
– Highest speed (0–99.9 km / h)
– Speed comparison
– Acceleration and deceleration
– Trip timer (max. 9:59:59) (countdown or forwards)

– Odometer (countdown or forwards)
– Total odometer and total cycling time display
– Calories
– Fat-burning
– Scan indicator (functions displayed in

continuous loop)

– Automatic switch to clock mode
– Backlight

Description of parts

Bracket

Sensor

Magnet

Battery 3 V

, type CR2032 button cell

Cable tie

Bike computer’s battery compartment cover

Bike computer

LC display

Function indicator

Secondary function value display

Primary function value display

MODE button

Light button

SET button

SCAN indicator

Servicing interval indicator

Speed comparison indicator

Acceleration / deceleration indicator:

Acceleration – anticlockwise rotation
Deceleration – clockwise rotation

Battery state indicator

Technical data

Battery:

3 V

(CR2032 button cell)

Included items

1 Bike computer
1 Bike computer bracket
1 Magnet
1 Sensor
6 Cable ties
1 Battery 3 V

, type CR2032 button cell

1 Operating instructions

General safety advice

KEEP ALL THE SAFETY ADVICE AND INSTRUC-
TIONS IN A SAFE PLACE FOR FUTURE REFERENCE!

Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited must
never be allowed to use the device without

supervision or instruction by a person responsible
for their safety. Children must be supervised so
that they do not play with the product.

Please note that the warranty does not cover
damage arising from improper treatment, non-
observance of the operating instructions and
safety advice or unauthorised use.

Safety advice concerning

batteries

RISK OF LOSS OF LIFE!

If batteries are swallowed, it can lead to loss of
life. Seek medical attention if a battery is swallowed.

Remove the battery if the product is not to be
used for a long period.

CAUTION! RISK OF EXPLO-
SION! Never recharge single-use
batteries!

CAUTION! DANGER OF EXPLO-
SION! Always replace all batteries
at the same time and only use batteries

of the same type.

If the battery is exhausted, remove it from the
device immediately. Otherwise the battery is
more likely to leak.

Make sure you insert the battery the right way
round (polarity).

Keep the battery away from children. Do not
throw the battery into a fire. Never short-circuit
it or take it apart.

If your battery leaks, remove it from the device
immediately to prevent the device from being
damaged.

Do not let the fluid from a leaking battery come
into contact with your skin, eyes or mucous
membranes. In the event of contact with fluid
leaking from a battery, thoroughly flush the

affected area with water and / or seek the
advice of a doctor!

Before use

Remove the protective foil from the LC display

before first use.

Inserting the battery

To insert the battery

, proceed as shown in

Fig. A.

Attaching the bike computer

To attach the device, proceed as shown in
Figs. B to I.

Note: Make sure the cable is attached properly. It
must not get caught in the spokes or trail along them.

Preparing for use

Basic settings

Note: The LC display

comes on automatically

approx. 2 seconds after the battery

is inserted.

You are immediately offered a choice of languages.

Press the MODE-button

repeatedly until the

desired language appears.

Confirm your choice by pressing the SET but-
ton

. You move on automatically to select

the user profile.

Press the MODE button repeatedly until the
desired user profile (

ADVANCE or EASY)

appears.

Confirm your choice by pressing the SET but-
ton. Now you can choose the wheel size (SET
WS).

A four-digit number appears in the LC display.
Now enter the tyre circumference of your wheel

in mm. Press the MODE button repeatedly until
the desired number appears as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for each of the three
remaining digits.

Note: You can calculate your tyre circumference
by multiplying your tyre diameter by 3.1416.
The following list contains the tyre circumferences
of the most common cycle tyres.

Tyre diameter

Tyre circumference

20”

1598 mm

22”

1759 mm

24”

1916 mm

26” (650 A)

2073 mm

26.5” (tubular)

2117 mm

26.6” (700x25C)

2124 mm

26.8” (700x28C)

2136 mm

27” (700x32C)

2155 mm

28” (700B)

2237 mm

ATB24”x1.75

1888 mm

ATB26 x1.4

1995 mm

ATB26 x1.5

2030 mm

ATB26 x1.75

2045 mm

ATB26x2 (650B)

2099 mm

27”x1

2138 mm

27”x1 1 / 4

2155 mm

Now select your desired unit of distance. Press
the MODE button repeatedly until SET KM or
SET MILE appears in the LC display.

Confirm your choice by pressing the SET button.
You move on to entering your age.

A two-digit number appears in the LC display.
Now enter your age. Press the MODE button
repeatedly until the desired number appears
as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for the remaining digit. You
move on to selecting the unit of weight.

Press the MODE button repeatedly until SET
KG or SET LB appears in the LC display.

Confirm your choice by pressing the SET button.
You move on to entering your weight.

A three-digit number appears in the LC display.
Now enter your weight. Press the MODE button
repeatedly until the desired number appears
as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for all the remaining digits.
You move on to selecting the time format.

Press the MODE button repeatedly until 12 for
the 12-hour format or 24 for the 24-hour format
appears in the LC display.

Confirm your choice by pressing the SET button.
You move on to setting the time.

A four-digit number appears in the LC display.
Enter the current time. Press the MODE button
repeatedly until the desired number appears
as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for all the remaining digits.
You move on to selecting the servicing interval.

Press the MODE button repeatedly until the
desired number of units of distance to your next
intended bicycle service appears in the LC
display.
Note: You have the choice of 200, 400, 600
or 800 km or miles.

Confirm your choice by pressing the SET button.
You move on to selecting the unit of temperature.

Press the MODE button repeatedly until °C or
°F appears in the LC display.

Confirm your choice by pressing the SET button.
You have now completed the the basic settings.

Using the bike computer

Note: If the bike computer remains unused for
more than 5 minutes, it automatically switches
into the stand-by mode. Press any button to

reactivate the computer. The function indicator

shows the current mode.

Press the MODE button

repeatedly to

page through the various modes.

Press the SET button

to change into the sec-

ondary function for any function.

Press the SET button and keep it pressed to call
or reset up any saved values.

The bike computer has the following
functions:

Advanced users’ functions:
CLOCK > TOTALODO > TOTAL-TM > TRIPDIST >
MAXSPEED > AVGSPEED > TRIPTIME > TEMP >
STPWATCH > CAL RATE > CALORIE > FAT-BURN >
KM+/- > TIME+/- > SCAN
Beginners’ functions:
TRIPDIST > AVGSPEED > TRIPTIME

Using functions

Note: All the functions and secondary functions
are described in the following list.
CLOCK: - Displays the time

Press the SET button

and keep it pressed for

3 seconds to access the time settings.

TOTALODO: - Total odometer

Press the SET button and keep it pressed for
3 seconds to access the wheel size settings
and total distance.

TOTAL-TM: Total time cycling

Press the SET button and keep it pressed for
3 seconds to make changes to the saved total
time cycling.

TRIPDIST: Trip distance

Press the SET button and keep it pressed for
3 seconds to reset the trip distance, the
average speed and the trip time displays to 0.

MAXSPEED: Highest speed

Press the SET button and keep it pressed for
3 seconds to reset

the maximum speed display

to 0.

AVGSPEED: Average speed
TRIPTIME: Trip time
TEMP: Thermometer

Press the SET button and keep it pressed to
switch between °C and °F.

Press the SET button to display the highest tem-
perature (HI) measured so far.

Press the SET button again to display the low-
est temperature (LO) measured so far.

Press and hold down the SET button while the
highest or lowest temperature is displayed to
switch back to the current temperature to
reset the saved data.

STPWATCH: Stopwatch

Press the SET button to start the stopwatch.

Press the SET button again to stop the stop-
watch.

Press the SET button and keep it pressed to
reset the stopwatch to 0.

CAL RATE: Current calorie consumption
CALORIE: Calorie meter

Press the SET button and keep it pressed to
reset the calorie counter to 0.

FAT-BURN: Fat burning in grams

Press the SET button and keep it pressed to
reset the fat burning value to 0.

KM: Odometer

Press the SET button and keep it pressed to
change the odometer settings.

The LC display

shows the symbol for count-

ing forwards or backwards (+ or - respectively).
Press the MODE button

repeatedly until the

desired symbol is shown.

Confirm your choice by pressing the SET button.
You move on to setting the distance on the
odometer.

A 5-digit number appears in the LC display. Enter
the desired distance. Press the MODE button
repeatedly until the desired number appears
as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for all the remaining digits.

TIME: Timer

Press the SET button and keep it pressed to
change the timer settings.

The LC display shows the symbol for counting
forwards or backwards (+ or - respectively).
Press the MODE button repeatedly until the
desired symbol is shown.

Confirm your choice by pressing the SET button.
You move on to the time settings of the timer.

A 5-digit number appears in the LC display.
Enter the desired time. Press the MODE button
repeatedly until the desired number appears
as the first digit.

Confirm your choice by pressing the SET button.

Repeat this process for all the remaining digits.

SCAN: Scan
Note: The scan mode automatically switches
between the trip distance, highest speed, average
speed and trip time displays.
Note: Refer to the section on “Basic settings” to
see how you make or change settings.

CUSTOMIZE mode

Apart from the ADVANCE and EASY mode, you
can make your individual adjustments in the
CUSTOMIZE mode (see procedure).

Press and hold the light button

to enter the

CUSTOMIZE mode.

Note: By repeatedly pressing the MODE
button

, you can toggle between the

ADVANCE and EASY modes.

In the EASY mode, press and hold the SET
button

. Press the MODE button to switch

the settings on or off (e.g. time). Choose „On“,
to add the chosen adjustment to the EASY
modes. Choose „Off“, if you do not want to
add the adjustments.

Press the SET button, to confirm your entry.

Using the backlight

Press the light button

to switch on the back-

light temporarily. The backlight automatically
extinguishes after a short period.

Resetting the bike computer

Press the MODE button

and SET button

at the same time and keep them pressed until
{{----}} appears in the LC display

Now press the MODE button and keep it
pressed. This resets all the settings.

Note: All stored data will be deleted.

Changing the battery

Note: The battery of the bike computer must be
replaced when the battery symbol

appears on

the LC display

Press the MODE key

and the SET key

at the same time and keep them pressed until
the {{-----}} symbol appears in the LC display

To replace the battery, proceed as shown in
figure A. Make sure you fit the battery the right
way round (polarity). This is shown inside the
battery compartment.

Press the SET key and keep it pressed to return
to normal operating mode.

Note: Once the batteries are removed, all stored
data will be erased after approx. 20 seconds.

Troubleshooting

Note: This device has delicate electronic compo-
nents. Therefore interference may occur when it is
near devices which transmit radio signals.
- If errors occur in the display, remove any such
devices from the vicinity of the product. In the case
of such malfunctions, remove the battery briefly and
then reinsert again.

Problem

Solution

Empty LC-display or no
response after putting
the battery in again

RESET

Remove battery. In the
area marked RESET of
the battery compartment,
touch the plus and minus
terminals at the same
time using a screwdriver.
Insert a 3V battery into
the battery compartment
in such a way that the +
terminal points upwards.
Replace the battery cover
on the battery compart-
ment. The microprocessor
is reset and restarted.

Speed or distance are
not displayed.

Adjust magnet and
sensor correctly.
- Check that the battery

is inserted with the
poles arranged the
right way round.

Display is black

The ambient temperature
is too high or the bicycle
computer was exposed
to direct sunlight for too
long. Remove appliance
from direct sunlight and
let it cool off for a while.

The LC-display shows
irregular symbols.

Remove battery and
replace it again.

Z31335

2 1b

8
9

BIKE COMPUTER

Operation and Safety Notes

CYKELCOMPUTER

Brugs- og sikkerhedsanvisninger

79107_cri_Fahrradcomputer_GB-IE-DK.indd 1

09.10.12 09:02

Advertising

Popular Brands

Popular manuals