Sealey SA141 User Manual
Sa141, Instructions for, Model no
INSTRUCTIONS FOR:
AIR IMPACT WRENCH 1/4” SQ. DRIVE
DIESEL GLOW PLUG KIT
MODEL NO:
SA141
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
4. AIR SUPPLY
Follow all Health & Safety and general workshop rules, regulations and conditions when using the wrench.
WARNING! Disconnect from air supply before changing accessories or servicing.
Maintain the
wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
Only use impact sockets which are specifically designed for use with an impact wrench.
Wear approved safety eye/face shield, ear defenders and hand protection.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
Keep children and non-essential persons away from the work area.
DO NOT use the wrench for a task that it is not designed to perform.
WARNING! DO NOT use wrench if damaged or thought to be faulty (contact your Service Agent).
DO NOT use wrench unless you have been instructed in its use by a qualified person.
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
DO NOT operate the wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
To avoid unintentional starting
DO NOT carry the wrench with your finger on the trigger.
DO NOT direct air from the air hose at yourself or others.
When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
Reduced torque impact wrench suitable for the removal of seized glow plugs on diesel engines. Features a four position air regulator which
provides limited torque settings to suit. One-hand operation for trigger and forward/reverse control. Soft grip reduces vibration, chill effect
and adds comfort. Handle exhaust helps to lower noise level during use. Includes five deep impact sockets, extension bar and universal
joint. Supplied with foam insert and metal case for storage.
Model No: . . . . . . . . . . . . . . . . . . . . SA141
Drive: . . . . . . . . . . . . . . . . . . . . . . . . 1/4”Sq
Torque Settings: . . . . . . . .10, 20, 30, 40Nm
Free Speed: . . . . . . . . . . . . . . . . 10000rpm
Air Consumption: . . . . . . . . . . . . . . . . .5cfm
Operating Pressure: . . . . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . 1/4”BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . 0.8kg
Noise Power: . . . . . . . . . . . . . . . . . . 102dB
Noise Pressure: . . . . . . . . . . . . . . . . . 91dB
Vibration: . . . . . . . . . . . . . . . . . . . . .5.1m/s²
Uncertainty: . . . . . . . . . . . . . . . . . .2.04m/s²
Refer to
instruction
manual
Wear ear
protection
Wear eye
protection
Wear
protective
gloves
4.1. Air Supply
Recommended hook-up is shown in fig 1.
4.1.1. Ensure that the wrench trigger is in the "Off" position before connecting the air supply.
4.1.2. You will require an air pressure of 90psi and an air flow of 4cfm.
WARNING! Ensure that the air supply is clean and does not exceed 90psi. Too high an air pressure and/or unclean air will cause
excessive wear and may result in damage and/or personal injury.
4.1.3. Drain the compressor air tank daily. Water in the air line will damage the wrench.
4.1.4. Clean compressor air inlet filter weekly.
4.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). Hose internal diameter and the bores of
fittings should be 1/4” minimum.
4.1.6. Keep hose away from heat, oil and sharp edges. Before each use check hose for wear and make certain that all connections are
secure.
SA141 Issue: 1 - 10/11/14
Original Language Version
© Jack Sealey Limited