Sealey SA2004KIT - Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION

WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.

WARNING! Disconnect from the air supply before changing accessories, servicing or performing any maintenance.
 Maintain the tools in good condition (use an authorised service agent).

Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.

Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery and wear non-slip shoes.

WARNING! Always wear approved eye and hand protection when operating these tools.

Use face, dust, or respiratory protection in accordance with COSHH regulations.

WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend that
suitable respiratory protection is worn.

Depending on the task, the tool noise level may exceed 84dB in which case wear safety ear defenders.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

Wear appropriate protective clothing and keep hands and body clear of working parts.

Keep children and unauthorised persons away from the work area.

Ensure that the workpiece is secure before operating the tool. Never hold a workpiece by hand.

DO NOT operate tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.

WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.

When not in use disconnect from air supply and store in a safe, dry, childproof location.

DO NOT use tool for a task that it is not designed to perform.

DO NOT operate tools if any parts are damaged or missing as this may cause failure and/or personal injury.

DO NOT carry the tool by the hose, or yank the hose from the air supply.

DO NOT place air line attachments close to your face and do not point at other people or animals.

DO NOT direct air from the air line at yourself or others.

DO NOT operate tools unless you have been instructed in their use by a qualified person.

DO NOT carry tools with your finger on the trigger and avoid unintentional starting.

DO NOT drop, throw or abuse the tools as they are precision instruments.

DO NOT leave the tools operating unattended.

DO NOT get the tools wet or operate in damp or wet locations.

DO NOT allow tools to free run for an extended period of time as this will shorten their life.
INSTRUCTIONS FOR:
4 PIECE AIR TOOL KIT WITH
ACCESSORIES
MODEL No:
SA2004KIT
Comprises, 150mm Air Hammer, 1/2” Air Impact Wrench, 1/2” Air Ratchet Wrench, 1/4” Air Die Grinder, 3x 125mm Chisels, Spring Retainer,
3/8” to 1/2” Adaptor, 1/2” Drive Impact Sockets - 10, 11, 13, 14, 15, 17, 19, 22, 24, 27mm, 3” Extension Bar, 3x 1/4” Grinding Stones, 5x Nipples,
1/4” (F) Quick Coupler, Air Tool Oil, 2 Wrenches and Allen Key, all in a composite carry case. Suitable for workshop and body shop applications.
Original Language Version SA2004KIT Issue:3(SP)-18/06/13 © Jack Sealey Limited