Sealey MAT150AS User Manual
Dust-free air operated sanders, Safety instructions, Instructions for
INSTRUCTIONS FOR:
DUST-FREE
AIR OPERATED SANDERS
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure that Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this equipment.
WARNING! Disconnect from air supply and dust-free system before changing accessories, servicing or
maintenance.
Maintain the
sander in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
Use the sander in a suitable work area. Keep area clean, tidy and free from unrelated materials. Ensure that
there is adequate lighting.
Before each use check abrasive pad for condition. If worn or damaged replace immediately.
Ensure that there are no flammable or combustible materials near the work area.
WARNING! Always wear approved eye or face protection when operating the sander.
If dust is generated, use face, dust, or respiratory protection in accordance with COSHH regulations.
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
Remove ill fitting clothing. Remove ties, watches, rings and loose jewellery. Contain and/or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Check moving parts alignment on a regular basis.
Ensure that the workpiece is correctly secured before operating the sander. Never hold a workpiece by hand.
Check the workpiece to ensure that there are no protruding nails, screws, stones, etc.
Avoid unintentional starting.
WARNING! Ensure that the correct air pressure is maintained and not exceeded.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
Prolonged exposure to vibration from these tools poses a health risk. It is the owner’s responsibility to correctly
assess the potential hazard, issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the sander for a task it is not designed to perform.
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
WARNING! DO NOT cut, grind, saw or sand any materials containing asbestos.
DO NOT carry the sander by the hose, or yank the hose from the air supply.
DO NOT get the sander wet or use in damp or wet locations.
DO NOT use the sander with water. These models are dry sanders only.
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT use sander where there are flammable liquids, solids or gases, such as paint solvents and including
waste wiping or cleaning rags etc.
DO NOT oil the sander, or connect to an air supply which incorporates an oiler. Oiling will result in damage to
teflon surfaces within the sander.
DO NOT leave the sander operating unattended.
DO NOT carry the sander with your finger on the power lever.
DO NOT direct air from the air hose at yourself or others.
When not in use disconnect from air supply and dust-free system, and store in a safe, dry, childproof location.
Model Nos:
MAT110AS MAT150AS MAT150SC
MAT150AS, MAT150SC, MAT110AS Issue No 2 (SP) 21/08/13
Original Language Version
© Jack Sealey Limited 2013