Sealey SG14 - Manual

1. SAFETY INSTRUCTIONS
 WARNING! Disconnect the gun from the air supply before changing accessories, servicing or performing any
maintenance.
 Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
 Keep the gun clean and rinse out nozzle and pipes with thinners
after use.
 WARNING! If gun components become blocked there is a danger
of excessive pressure building up in unit causing the canister to burst.
 Locate the gun in a suitable, well ventilated area. Keep area clean,
tidy and free from unrelated materials and ensure there is adequate
lighting.
 Remove ill fitting clothing. Remove ties, watches, rings and other
loose jewellery and contain long hair.

Keep children and unauthorised persons away from the working area.

Avoid unintentional operation.

Ensure coating/wax manufacturer’s instructions are carefully
followed.

DO NOT hold gun or attachments close to your face (especially
eyes, ears, etc.) and do not point gun or air hose at other persons
or animals.
 DO NOT carry by the air hose, or yank the hose or the gun from
the air supply.
 DO NOT use the gun for any purpose other than for which it is
designed and do not use with any other fluid.
 DO NOT operate the gun if damaged.
 When not in use disconnect from the air supply and store in a safe,
dry, childproof area.
2. INTROdUCTION & SPECIFICATION
Accepts most popular types of 1ltr coating tins.
3.1 AIR SUPPlY (For recommended hook-up, see fig.2.)
3.1.1 Ensure air valve is in "off" position before
connecting to the air supply.
3.1.2 An air pressure of no more than 90psi and an air
volume of 8cfm will be required.
3.1.3  WARNING! Ensure air supply does not
exceed 90psi. Too high a pressure will shorten
the product life and may be dangerous, causing
damage and/or personal injury.
3.1.4 Drain air supply tank daily. Water in the air line will
damage the gun and will invalidate your warranty.
3.1.5 Clean air inlet filter screen weekly.
3.1.6 Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose and fittings diameter should be 10mm I.D.
3.1.7 Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3. PREPARING THE GUN FOR USE
Fig 2
Air Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption:. . . . . . . . . . . . . . . . . . . . . . . 8cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PlEASE REAd THESE INSTRUCTIONS CAREFUllY. NOTE THE SAFE OPERATIONAl REQUIREMENTS,
WARNINGS ANd CAUTIONS. USE THIS PROdUCT CORRECTlY ANd WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENdEd. FAIlURE TO dO SO MAY CAUSE dAMAGE ANd/OR PERSONAl INJURY ANd WIll INVAlIdATE
THE WARRANTY. PlEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRuCTIONS FOR:
UNdER-bOdY COATING GUN
MODEL NO:
SG14.V3
Fig 1
Original Language Version SG14.V3 Issue: 2 - 09/12/09