Sealey RE99/09 - Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instruc-
tions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
WHEEL ARCH PULLERS
MODELS:
RE99/09 & RE99/10
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
E-mail: [email protected]
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
Suitable for wheel arches and other small/lightweight pulls
including those around light clusters.
Model No: . . . . . . . .RE99/09
Length: . . . . . . . . . . .320mm
Capacity: . . . . . . . . . . .1.5ton
Model No: . . . . . . . .RE99/10
Length: . . . . . . . . . . .160mm
Capacity: . . . . . . . . . . .1.5ton
RE99/10
RE99/09
2. INTRODUCTION AND SPECIFICATIONS
3. USING THE WHEEL ARCH PULLER
1. SAFETY INSTRUCTIONS
3.1 USING THE PULLERS
3.1.1 Carefully select the appropriate puller and curvature for the job in hand.
3.1.2 For slight dents and creases the tool can be pulled by hand.
3.1.3 With more severe dents and creases, use of chassis straighteners DZRE84/C or DZRE92/C is recommended.
Refer to DZRE84/C or DZRE92/C instructions for detailed information.
o ALWAYS! Use in conjunction with a safety cable to prevent injury in the event of the puller slipping during pulling
operation (See item RE92/SC).
p WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly
adhered to when using the puller.
7 DO NOT use puller if damaged or worn.
3 Maintain the puller in good and clean condition for best and safest performance.
3 Always check that puller is correctly assembled and is square with the workpiece.
3 If vehicle is raised, ensure it is adequately supported with axle stands, ramps, etc. as
appropriate.
3 Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
3 Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
3 Where possible shield workpiece with canvas or similar to provide protection against failed parts.
7 DO NOT hit workpiece with a hammer if workpiece has not moved with maximum puller force applied. Use a larger
capacity puller.
7 DO NOT use the puller for a task it is not designed to perform.
o o IMPORTANT! Always refer to the vehicle manufacturer’s service instructions, or proprietary manual, to establish the
correct procedure and data. These instructions for use are provided as a guide only.
RE99/09 & RE99/10 - 1 - 120705
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instruc-
tions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
WHEEL ARCH PULLERS
MODELS:
RE99/09 & RE99/10
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
E-mail: [email protected]
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
Suitable for wheel arches and other small/lightweight pulls
including those around light clusters.
Model No: . . . . . . . .RE99/09
Length: . . . . . . . . . . .320mm
Capacity: . . . . . . . . . . .1.5ton
Model No: . . . . . . . .RE99/10
Length: . . . . . . . . . . .160mm
Capacity: . . . . . . . . . . .1.5ton
RE99/10
RE99/09
2. INTRODUCTION AND SPECIFICATIONS
3. USING THE WHEEL ARCH PULLER
1. SAFETY INSTRUCTIONS
3.1 USING THE PULLERS
3.1.1 Carefully select the appropriate puller and curvature for the job in hand.
3.1.2 For slight dents and creases the tool can be pulled by hand.
3.1.3 With more severe dents and creases, use of chassis straighteners DZRE84/C or DZRE92/C is recommended.
Refer to DZRE84/C or DZRE92/C instructions for detailed information.
o ALWAYS! Use in conjunction with a safety cable to prevent injury in the event of the puller slipping during pulling
operation (See item RE92/SC).
p WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly
adhered to when using the puller.
7 DO NOT use puller if damaged or worn.
3 Maintain the puller in good and clean condition for best and safest performance.
3 Always check that puller is correctly assembled and is square with the workpiece.
3 If vehicle is raised, ensure it is adequately supported with axle stands, ramps, etc. as
appropriate.
3 Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
3 Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
3 Where possible shield workpiece with canvas or similar to provide protection against failed parts.
7 DO NOT hit workpiece with a hammer if workpiece has not moved with maximum puller force applied. Use a larger
capacity puller.
7 DO NOT use the puller for a task it is not designed to perform.
o o IMPORTANT! Always refer to the vehicle manufacturer’s service instructions, or proprietary manual, to establish the
correct procedure and data. These instructions for use are provided as a guide only.
RE99/09 & RE99/10 - 1 - 120705