Sealey SA894 User Manual
Instructions for, Safety instructions, Introduction and specification
SA894.V3, SA895.V3 - 1 - 010806
INSTRUCTIONS FOR:
RETRACTING AIR HOSE REELS
MODELS: SA894.V3 AND SA 895.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1.
SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
!
Familiarise yourself with the application and limitations of the air hose reel, as well as the specific hazards.
"
WARNING! Disconnect the air hose reel from the air supply before changing accessories, servicing or performing any maintenance.
!
Maintain the air hose reel in good condition (use an authorised service agent).
!
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
!
Locate and fix the air hose reel in a suitable working area. Do not position the hose in direct sun light, or in areas of extreme heat or
cold. Ensure there is adequate lighting.
"
WARNING! Ensure maximum air pressure is not exceeded.
!
Keep extended air hose away from heat, oil and sharp edges. Check hose for wear before each use, and ensure all connections are secure.
!
Keep the unwound air hose at a safe distance from the working area and free from wet, damp, oily surfaces.
"
WARNING! Always wear approved eye or face protection when operating the air hose reel.
!
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
!
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery and contain and/or tie back long hair.
!
Keep children and unauthorised persons away from the working area.
#
DO NOT operate the air hose reel if any parts are damaged or missing as this may cause failure and/or personal injury.
#
DO NOT exceed the rated capacity of the air hose reel.
#
DO NOT use the air hose reel for any purpose other than that for which it is designed.
#
DO NOT yank the hose from the air supply.
#
DO NOT operate the air hose reel when you are tired or under the influence of alcohol, drugs or intoxicating medication.
#
DO NOT direct air from the air hose at yourself or others.
!
When not in use ensure the air supply is turned off and tools disconnected. Disconnect from the air supply and retract the hose into case.
"
WARNING! DO NOT dismantle the hose reel casing. To do so may result in damage to the appliance and/or personal injury and will
invalidate the warranty. Internal maintenance, which will require the opening of the casing, must only be undertaken by an authorised
service agent.
2.
INTRODUCTION AND SPECIFICATION
2.1
Introduction
Models SA 894.V3 and SA895.V3 have a hard wearing composite casing with retracting air hose reel. Ratchet and free-running
operation enables easy access to locations within the extended air hose range. Both reels can be wall or ceiling mounted and
come complete with attachment brackets. Refer to Fig.1.
3.
MOUNTING AND ASSEMBLY
"
WARNING! Ensure the hose is disconnected from the air supply. DO NOT
position the hose in direct sunlight or in areas of extreme heat or cold.
3.1.
To wall mount the reel first remove the wall mounting bracket from the reel by
releasing and withdrawing the two bracket pivots. (Refer to items 11 on the parts
diagram for the SA894 & SA895.) To release the pivots remove the casing
screws which pass directly through each pivot. (The pivots for SA894 & SA895
are each retained by two screws.)
"
WARNING! DO NOT remove any other casing screws.
3.2.
Fix the bracket in an appropriate position ensuring that the wall and the
mounting screws and plugs will adequately support the weight of the reel and
the tension of the hose as it is pulled from the reel.
3.3.
Re-attach the reel to the bracket ensuring that the pivots are correctly inserted
and retained by the casing screws.
3.4.
Ensure that the hose can be pulled out to, and reeled back from, work sites
without rubbing on the sides of the cable entry.
2.2
Specification
Model No . . . . . . . . . . . . . . . . SA894.V3. . . . . . . . . . . . . . . . . . . . . SA895.V3
Hose length . . . . . . . . . . . . . . . . . . . 15mtr. . . . . . . . . . . . . . . . . . . . . . . .10mtr
Hose ID/OD . . . . . . . . . . . . . . . . . 8/12mm. . . . . . . . . . . . . . . . . . . . .10/15mm
Maximum pressure . . . . . . . . . . . . 150psi. . . . . . . . . . . . . . . . . . . . . .. . .150psi
Hose type . . . . . . . . . . . . . . Polyurethane. . . . . . . . . . . . . . . . . . . Polyurethane
Inlet - Outlet . . . . . . . . . . . . . . . . .1/4”BSP. . . . . . . . . . . . . . . . . . . . . . .3/8”BSP
Fig. 1