Sealey AK2020 - Manual

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
AK2020 - 1 - 021202
01284 757500
[email protected] 01284 703534
Sole UK Distributor,
Sealey Group, Bury St. Edmunds, Suffolk.
INSTRUCTIONS FOR:
MOISTURE METER
Model:
AK2020
1. INTRODUCTION
2. INSTRUCTIONS
AK2020 is designed to indicate the moisture content of timber in the range 8 to 22%, with colour coded ranges for
readings taken on plaster or brick.
Web
e-mail
www.sealey.co.uk
p p WARNING! Always replace the probe cover after use to prevent injury, damage to the probes and shorting.
2.1.
Battery
2.1.1. Slide off the battery compartment cover, in the rear of the unit.
2.1.2. Connect a 9V type MN1604 (06LR61) battery (not supplied) to the terminal pad.
2.1.3. Place the battery in the compartment and replace the cover.
2.1.4. Replace the battery when the Low Battery LED (B) is illuminated.
2.2.
Operation
2.2.1. Remove the probe cover (A) and stow on the end (E) of the unit.
2.2.2. Slide the side-mounted switch (D) to the On position. The Power LED (C) will illuminate.
2.2.3. Press the two probes into the material to be tested and note the reading on the LED scale (F).
2.2.4. Switch off the unit and replace the probe cover after use.
2.3.
Readings
2.3.1. When used on the timber the percentage scale should be used.
2.3.2. When used on plaster, brick or similar materials read the colour codes as follows:
Blue - Air-dry, OK.
Yellow - Slightly damper than air-dry, investigate.
Red - Excessive moisture, indicating a damp problem.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
AK2020 - 1 - 021202
01284 757500 [email protected] 01284 703534
Sole UK Distributor,
Sealey Group, Bury St. Edmunds, Suffolk.
INSTRUCTIONS FOR:
MOISTURE METER
Model:
AK2020
1. INTRODUCTION
2. INSTRUCTIONS
AK2020 is designed to indicate the moisture content of timber in the range 8 to 22%, with colour coded ranges for
readings taken on plaster or brick.
Web
e-mail
www.sealey.co.uk
p p WARNING! Always replace the probe cover after use to prevent injury, damage to the probes and shorting.
2.1. Battery
2.1.1. Slide off the battery compartment cover, in the rear of the unit.
2.1.2. Connect a 9V type MN1604 (06LR61) battery (not supplied) to the terminal pad.
2.1.3. Place the battery in the compartment and replace the cover.
2.1.4. Replace the battery when the Low Battery LED (B) is illuminated.
2.2.
Operation
2.2.1. Remove the probe cover (A) and stow on the end (E) of the unit.
2.2.2. Slide the side-mounted switch (D) to the On position. The Power LED (C) will illuminate.
2.2.3. Press the two probes into the material to be tested and note the reading on the LED scale (F).
2.2.4. Switch off the unit and replace the probe cover after use.
2.3.
Readings
2.3.1. When used on the timber the percentage scale should be used.
2.3.2. When used on plaster, brick or similar materials read the colour codes as follows:
Blue - Air-dry, OK.
Yellow - Slightly damper than air-dry, investigate.
Red - Excessive moisture, indicating a damp problem.