Sealey TS10SEW - Manual

InstructIons for:
254mm TABLE SAW WiTh STAnd
& ExTEnSion TABLES
Model no : TS10SEW.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY inSTRUCTionS
IMPORTANT: PLEASE REAd ThESE inSTRUCTionS CAREFULLY. noTE ThE SAFE oPERATionAL REQUiREMEnTS, WARninGS And
CAUTionS. USE ThiS PRodUCT CoRRECTLY And WiTh CARE FoR ThE PURPoSE FoR WhiCh iT iS inTEndEd. FAiLURE To do So MAY
CAUSE dAMAGE And/oR PERSonAL inJURY And WiLL inVALidATE ThE WARRAnTY. PLEASE KEEP inSTRUCTionS SAFE FoR FUTURE USE.
1.1. ELECTRiCAL SAFETY
 WARninG! it is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances, before using, to ensure that they are safe. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board. We also
recommend that an rcd (residual current device) is used with all electrical products. It is particularly important to use an rcd with portable
products that are plugged into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician. You may obtain a residual
current device by contacting your sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. see 1.1.1. & 1.1.2.
above and use a Portable Appliance tester (PAt).
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply leads, plugs for wear and damage and power connections, to
ensure that none is loose.
1.1.6. Important: ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may
require a fuse smaller than 13 amps for certain products, see fuse rating at right.
1.1.7. do noT pull or carry the appliance by its power supply lead.
1.1.8. do noT pull the plug from the socket by the power cable.
1.1.9. do noT use worn or damage leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician. A u.K. 3 pin plug with AstA/Bs approval is fitted. In case of
damage, cut it off and fit a new plug according to the following instructions (discard old plug safely).
(uK only - see diagram at right). Ensure the unit is correctly wired via a three-pin plug.
a) Connect the yellow/green earth wire to the earth terminal ‘E’.
b) Connect the brown live wire to live terminal ‘L’.
c) Connect the blue neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products are fitted with live (BroWn) and neutral (Blue) wires only. double insulated products are always
marked with this symbol . To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue
to the earth terminal.
1.1.10. some products require more than a 13 amp electrical supply. In such a case, no plug will be fitted. You must contact a qualified
electrician to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and
socket with your electrician.
1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an rcd
fitted is recommended since any product which is plugged into the cable reel will be protected. the section of the cores of the cable
is important and should be at least 1.5mm2, but to be absolutely sure that the capacity of the cable reel is suitable for this product and
for others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2. GEnERAL SAFETY
 familiarise yourself with the applications, limitations and potential hazards of the saw.
 WARNING! disconnect the saw from the mains power before changing accessories, servicing or performing any maintenance.
 the machine must only be serviced by a qualified person or service agent. contact your sealey dealer for information.
 select a work area suitable for the saw and keep the area clean, tidy and free from unrelated materials. ensure that there is adequate lighting.
 stand the saw on a stable floor strong enough to take the weight of the machine and workpiece.
 Wood dust can be harmful to health by inhalation and skin contact and concentrations of small dust particles in the air can form an
explosive mixture. ensure that there is adequate ventilation and that the saw is attached to a dust-extraction unit.
 Maintain the saw in good condition, check moving parts alignment regularly. Keep saw blades clean and sharp. ,
 replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
 WARNING! Keep all guards in place and in good working order. check regularly for damaged parts.
A guard, or any other part, that is damaged must be repaired or replaced before the saw is next used. the safety guard is a
mandatory fitting where the saw is used on premises covered by the Health & safety at Work Act.
 Before commencing work, ensure that the saw blade is set to cut in the correct direction, securely fastened, sharp and is compatible
with the machine, spindle speed and the material to be cut. never use a saw blade if damaged, bent or warped. use only
recommended saw blades.
 remove adjusting keys and wrenches from the machine and the vicinity before switching on.
 Machine operators must have received sufficient training and instructions relating to the dangers associated with the machine, the
precautions to be observed and those requirements of the Wood Working Machines regulations which apply. Inexperienced
operators must be under the adequate supervision of a person who has a thorough knowledge and experience of the machine and the
required guards.
 do noT operate the saw if any parts are damaged or missing as this may cause product failure and/or personal injury.
Original Language Version ts10seW.V2 Issue: 1 - 11/07/13
SUGGESTEd FUSE
RATinG: 13A
© Jack sealey limited