Sealey PROJ12 - Manual

INSTRUCTIONS FOR:
PROJUMP
Models:
PROJ12 & PROJ12/24
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATIONS
DANGER! - BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON,
IT IS VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE PROJUMP EQUIPMENT.
Follow these instructions and those published by the battery manufacturer, and the maker of any equipment you intend to use in the
vicinity of the battery. Remember to review warning marks on all products and on engines. ,
1.1. PERSONAL PRECAUTIONS
3 Ensure that Health & Safety, local authority, and general workshop practice regulations are adhered to when using
this equipment.
3 Ensure that there is another person with you especially within hearing range of your voice, or close enough to come to your aid should a problem
arise when working near a lead-acid battery.
3 Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current high
enough to weld a ring or the like to metal, which may cause severe burns.
3 Ensure that hands and clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair.
3 Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
7 DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.
7 DO NOT drop any metal tool onto the battery as It may spark or short circuit the battery which could cause an explosion.
7 DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.
1.2. GENERAL SAFETY INSTRUCTIONS
3 Familiarise yourself with the application, limitations and potential hazards relating to this product. Also, refer to the vehicle manufacturer’s
handbook. IF IN ANY DOUBT CONSULT AN ELECTRICIAN.
3 Ensure that the Projump is in good order and condition before use. If in any doubt do not use the unit and contact an electrician.
7 DO NOT dis-assemble the Projump for any reason. The Projump must be checked only by qualified service personnel.
3 Only use recommended attachments and parts. To use unapproved items may be dangerous and
will invalidate your warranty.
p p WARNING! Check that both vehicle batteries are the same voltage.
3 Ensure that vehicles are not touching before attempting to use these leads.
3 Keep tools and other items away from the engines, and ensure that you can see the battery and
the working parts of the engine clearly.
3 Keep children and unauthorised persons away from the work area.
3 Ensure that the jump leads are not tangled and are clear of moving or hot engine parts.
7 DO NOT allow the clamps to touch each other or to make contact with the vehicle bodywork, as
this may result in arcing.
7 DO NOT cross connect the power leads to the battery. Ensure positive is to positive and negative is to negative.
7 DO NOT pull the cables or clamps from the battery terminals.
7 DO NOT operate in the vicinity of flammable liquids or gases.
7 DO NOT try to jump start a frozen battery.
7 DO NOT use or store the Projump in damp or wet locations.
7 DO NOT use this product to perform a task for which it is not designed.
3 The cables may become hot with excessive use. If so, allow a few minutes for them to cool before attempting to re-use.
3 If the Projump receives a sharp knock or blow, the unit must be checked by a qualified service agent before next use.
3 When not in use, store the Projump carefully in the bag provided and store in a safe, dry, childproof location.
2.1. Introduction
Many of today's vehicles are crammed with sensitive electronic equipment including ECUs, Air Bag sensors, Digital Dashes, Alarms, Car Radios,
Telephones and In-Car Security Systems. The potential for damage to these items from carrying out even basic work on the vehicle is huge.
Transient spikes and surges generated by making/breaking contacts can 'fry' electronic cards or, at the very least, lead to premature failure.
By using the PROJUMP Surge Protected Booster Cables, you will protect not only your own vehicle from these dangers, but also the 'sick' vehicle.
The ‘Traffic Light‘ system clearly shows if it is safe to proceed with the jump-start before any serious damage can be done.
2.2.
Specifications
Model No. Voltage Cable Section Length
PROJ12 . . . . . . . . . . . . 12V . . . . . . . . 20mm 2 . . . . . . . . . . . 5m
PROJ12/24. . . . . . 12 or 24V . . . . . . . . 25mm 2 . . . . . . . . . . . 7m
PROJ12 & PROJ12/24 - 2 - 291002