Sealey SM224 User Manual
Sm224, Air operated parts cleaning tank with reservoir, Safety instructions
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
AIR OPERATED PARTS CLEANING TANK
WITH RESERVOIR
INSTRUCTION MANUAL FOR MODEL:
SM224
WARNING! Ensure Health & Safety, local authority, general workshop practice regulations are adhered to when using equipment.
WARNING! Installation site must be equipped with suitable fire extinguishers (water must not be used) and escape routes.
WARNING! Disconnect the air supply from the tank before changing accessories, servicing or performing any maintenance.
Maintain the tank in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Locate the tank in a suitable work area. Ensure the tank stands on a firm, level surface. Keep area clean and tidy and free from unrelated
materials. Ensure the area is well ventilated and has adequate lighting.
WARNING! Ensure specified air pressure is maintained and not exceeded.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
WARNING! This tank is recommended for use only with degreasing solvents suitable for air operated tanks. Ensure you follow
makers instructions for solvent use.
Ensure solvent flash point is above 140°F. We recommend you use Sealey solvent - contact your local dealer for details.
Keep the tank clean. Remove and clean the tank filters regularly for best performance.
WARNING! DO NOT SMOKE and keep sources of ignition, such as heaters, lamps, etc., away from the unit, together with
flammable or combustible materials, as there is an explosion risk.
When cleaning parts ensure that nothing in the tank, including any parts basket, is in a position that would prevent the lid from
closing fully if and when the fusible link activates.
WARNING! DO NOT modify the lid or jam it open. Keep the lid and holding screws in place, tight and in good working order.
WARNING! DO NOT attempt to perform welding on the unit for any reason. Do not weld near the unit.
WARNING! Wear approved safety eye protection, mask and gloves. If solvent gets on skin or in eyes wash thoroughly with water
and take any other action as required by the solvent instructions.
Remove ill fitting clothing, ties, watches, rings and other loose jewellery, contain long hair and wear appropriate protective clothing.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep non-essential persons away from the working area.
In case of fire in tank, do not attempt to move unit or remove parts from tank. The lid is fusible and will automatically close extinguishing fire.
Disconnect the unit from the air supply when not in use.
DO NOT use the tank for any purpose other than that for which it is designed.
DO NOT operate the tank if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT over-fill the tank.
DO NOT modify or jam the parts washer lid open, as this will make the fusible fire link inoperative which is dangerous practice and will
invalidate the warranty and your insurance.
DO NOT use air line to blow dry components in tank. Only use air gun supplied. DO NOT direct air gun at yourself or others.
DO NOT leave the parts washer operating unattended.
When cleaning is complete, ensure all controls are in the ‘off’ position and that the air supply is disconnected.
WARNING! It is owner’s responsibility to ensure that there is no uncontrolled discharge of any fluids used with this unit and that
appropriate arrangements have been made for correct disposal of waste in accordance with government/local authority
regulations.
2. INTRODUCTION & SPECIFICATION
Steel fabricated 65ltr reservoir and 50ltr one-piece tank. Mobile
unit with two castors and two fixed wheels can be easily taken to
work area. Air operated unit can be charged and used remotely
without air supply for a limited period. Includes air blow gun for fast
drying and brush for cleaning workpiece. Reservoir fitted with fluid
level indicator and drain tap. Supplied with removable shelf and
tray. Lid fitted with fusible link hinge which automatically snaps
shut in the event of a fire.
SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SM224
Overall Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040mm
Tank Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180mm
Tank Width:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710mm
Maximum Length:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775mm
Pump Output/hr: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140ltr
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-60psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6cfm
Air Inlet Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23kg
Max. Working Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55ltr
Original Language Version
SM224 Issue: 3(SP) - 04/09/13
© Jack Sealey Limited