Sealey SB973 User Manual
Sb973.v3, Instructions for: shot blasting cabinet model no, Safety instructions 2. description & specification
1.2 GENERAL SAFETY
WARNING! Ensure Health & Safety, government and local authority regulations relating to shot blasting are adhered to when
using this equipment. Familiarise yourself with the application, limitations, and potential hazards peculiar to the cabinet.
WARNING! Disconnect cabinet from mains power and air supply before changing accessories, servicing or performing any maintenance.
Maintain the
cabinet in good condition Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous
and will invalidate the warranty.
Locate cabinet in a suitable working area. Keep area clean, tidy and free from unrelated materials. Ensure adequate lighting.
IMPORTANT: Use only dry abrasives such as glass bead, silica sand, aluminium oxide and other proprietary brands of
blasting media. We recommend Sealey item B5KG. Never use fluids or mix fluids with another media in unit.
WARNING! Always wear approved eye/face protection and ear protection when operating the cabinet.
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/or tie back long hair.
Keep the side door closed and secured when in use.
WARNING! Ensure correct air pressure is maintained and not exceeded.
Always keep blast nozzle directed at the workpiece. DO NOT aim blast at gloves, glove fingers or internal light. Never use outside the unit.
Regularly check that the exhaust vent at the back of the cabinet is clear and not blocked and there is space between it and any wall.
Maintain correct balance and footing. Ensure the floor is clean and free from blasting grit spillage. Wear non-slip shoes.
Keep children and non essential persons away from the working area.
DO NOT use the cabinet for a task it is not designed to perform.
DO NOT operate the cabinet if any parts are damaged or missing as this may cause failure and/or possible personal injury.
DO NOT operate the cabinet with the side door open.
DO NOT use the gun without appropriate nozzle fitted.
DO NOT stand on the cabinet.
DO NOT get the cabinet wet or use in damp or wet locations or areas where there is condensation.
DO NOT operate the cabinet when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT leave the cabinet operating unattended.
The viewing screen is 5mm tempered glass. If glass should break ensure you replace with tempered or safety glass only.
When not in use disconnect from the electrical mains and the air power supply.
NOTE! We strongly recommend that a suitable dust extraction system is used with this unit.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
INSTRUCTIONS FOR:
SHOT BLASTING CABINET
MODEL NO:
SB973.V3
1.1
ELECTRICAL SAFETY.
ONLY USE THE SUPPLIED TRANSFORMER PLUG FOR CONNECTING UNIT TO THE MAIN ELECTRICAL POWER SUPPLY.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all
electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3 You must ensure that you:
Inspect the transformer plug, cable, adaptor for wear and damage to ensure items are safe before connecting to the mains power supply.
If worn or damaged DO NOT use, immediately replace, or contact a qualified electrician.
Check cables are always protected against short circuit and overload.
Important: Check that the voltage marked on the transformer plug is the same as the power supply to be used.
Uncoil the power cable between the transformer and the powered product.
DO NOT pull transformer power lead, or pull the transformer plug from the mains socket by the power lead.
DO NOT use any other type of transformer with this product.
DO NOT place the power connector into any area of the product except the correct inlet socket.
DO NOT try to open or dis-assemble the transformer plug.
DO NOT use the transformer plug to power any other electrical item.
DO NOT get the transformer wet, or use in wet, damp conditions (for indoor use only).
WARNING! NEVER substitute a standard 13Amp 3 pin plug, or any other type of plug, for the transformer plug.
Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is
recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable reel is important.
We recommend that at least 1.5mm
2
section cable but to be absolutely sure that the capacity of the cable reel is suitable for this product and
for others that may be used in the other output sockets, we recommend the use of 2.5mm
2
section cable.
Heavy-duty steel cabinet with toughened glass viewing screen and integral low voltage illumination. Large single side door provides easy
access for bulkier items. Includes Ø60mm dust extraction port for a clear view. Heavy gauntlets provide hand protection and each cabinet is
supplied with sand blasting gun, four sizes of ceramic nozzle and a pack of five visor covers. Suitable for glass beads, silica sand, aluminium
oxide and other proprietary brands of blasting media.
1. SAFETY INSTRUCTIONS
2. DESCRIPTION & SPECIFICATION
Original Language Version
SB973.V3 Issue: 2 - 30/03/10