Sealey ES601 User Manual
Es601, Engine support beam with cross beam, Instructions for
Thank you for purchasing a Sealey Product. Manufactured to a high
standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
InstructIons For:
ENGINE SUPPORT BEAM WITH
CROSS BEAM
Model no:
ES601
ensure that the engine support is in good working order. take action for
immediate repair or replacement of damaged parts. Use genuine parts
only. The use of unauthorised parts may be dangerous and will invalidate
the warranty.
locate the vehicle in a suitable, well lit work area.
Keep work area clean and tidy and free from unrelated materials.
ensure the vehicle handbrake is engaged and the engine/motor is
switched off.
ensure all non-essential persons keep a safe distance whilst the engine
support is in use.
DO NOT use the engine support if damaged.
DO NOT allow untrained persons to operate the engine support.
DO NOT use the engine support for purposes other than that for which it
is designed.
DO NOT exceed the rated capacity of the engine support.
When not in use, store engine support in a safe, dry, childproof area.
WARNING! The warnings, cautions and instructions referred
to in this manual cannot cover all possible conditions and
situations that may occur. It must be understood that
common sense and caution are factors which cannot be
built into this product, but must be applied by the operator.
2. INTRODUCTION & SPECIFICATION
3. OPERATING INSTRUCTIONS
1. SAFETY INSTRUCTIONS
3.1. the fully assembled support beam is heavy and should be
lifted into place by two people.
3.2. loosen the grip knobs (fig1.1) to allow the assemblies to slide and then
locate the rubber feet into the gutters of the vehicle’s front wing panels or
close to the suspension strut towers. the feet can be adjusted to allow
the main beam to be installed in a level plane (fig1.5). When located,
tighten thoroughly.
note: refer to the manufacturer’s handbook to identify engine lifting
brackets.
If required, loosen the centre clamp (fig1.3) to swivel the cross beam
(fig1.7) to the desired alignment, then re-tighten.
3.3. drop the adjustable screw assemblies (fig1.6) through the slot in the
cross beam in positions adjacent to the engine lifting points. If not utilising
the swivel facility, the lift screw will pass through both the cross beam
(fig1.7) and main beam (fig1.8).
3.4. Attach the hooks to the lifting brackets on the engine and thread grip
knobs (fig 1.2) onto adjustable hook assemblies.
3.5. Progressively rotate the lifting handles (fig1.2) clockwise to support the
3.6
on completion of the maintenance task, rotate the lifting handles
anticlockwise to release the tension on the lifting hook assemblies
3.7. unhook, loosen both grips and remove the engine support from the
vehicle.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ES601
Maximum capacity: . . . . . . . . . . . . . . . . . . . . . . . 500kg
Main Beam Maximum Width . . . . . . . . . . . . . . 1400mm
Main Beam Minimum Width: . . . . . . . . . . . . . . . 140mm
cross Beam Maximum Width: . . . . . . . . . . . . . . 810mm
cross Beam Minimum Width:. . . . . . . . . . . . . . . 140mm
screw Hook lengths: . . . . . . . . . . . . . . . . . 410/320mm
designed to support and accurately position engines during
maintenance operations such as replacing anti-vibration mountings
and certain body panels. Also used as an aid for the removal of gear-
boxes and transmissions. Beams supported on rubber feet and fine
adjustment control is obtained by using screw/hook mechanisms. this
model has the additional advantage of a 360° adjustable rotating cross
beam to enable greater range of support options when in use.
fig.1
Environmental Protection.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which is compatible with the environment.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
© Jack sealey limited
es601 Issue: 1 20/03/13