Sealey ES450 - Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
INSTRUCTIONS FOR:
E N G I N E S TA N D 450kg
Model No :
ES450.V2
PARTS LIST
ITEM PART NO. DESCRIPTION
1 ES450.V2-01 MAIN POST
3 ES450.V2-03 SIDE LEG, FIXED
4 ES450.V2-04 BOLT (1/2”X3”)
5 ES450.V2-05 HEAD MOUNTING PLATE
6 ES450.V2-06 LOCKING PIN
7 ES450.V2-07 MOUNTING ARMS
8 ES450.V2-08 BOLT (1/2”X2 1/2”)
9 ES450.V2-09 FLAT WASHER 1/2”
10 ES450.V2-10 NUT (H3X1/2NC)
11 ES450.V2-11 LOCKING WASHER 1/2”
12 ES450.V2-12 FLAT WASHER 3/8”
14 ES450.V2-14 CASTER WHEEL
15 ES450.V2-15 NUT 3/8NC
17 ES450.V2-17 FLAT WASHER 3/4”
19 ES450.V2-19 LOCKING CLIP
20 ES450.V2-20 MAIN BEAM
21 ES450.V2-21 CASTOR LEG
22 ES450.V2-22 MAIN POST LABEL
23 ES450.V2-23 WHEEL 4”
24 ES450.V2-24 BOLT (3/8”X2 3/4”)
25 ES450.V2-25 LOCK WASHER 3/8”
26 ES450.V2-26 HANDLE (NOT SHOWN)
ES450.V2 - 1 - 031207
Note: All the following numbers refer to Fig.1 and parts list
below.
2.1. Remove mounting plate (5) from main post (1).
2.2. Loosely attach main post (1) to side leg (3) with bolts (24),
washers (12 & 25) and nuts (15).
2.3. Slide main beam (20) into base of main post (1) and loosely
secure with bolt (4).
Note: Main beam (20) must be assembled with bracket (A) as
shown.
2.4. Fit castor leg (21) to main beam (20) with bolts (24), washers
(12 & 25) and nuts (15).
Note: Castor leg (21) must be fitted with castor mounting
holes facing downward.
2.5. Tighten all nuts/bolts.
2.6. Fit castors (14) to castor leg (21) with nuts (10) and washers
(11 & 17).
2.7. Slide wheels (Fig.2.23) onto pins on wheel leg (3) and retain
with washers (17) and locking clip (19).
Note: Wheel hubs are not symmetrical - fit with longer hub
inward.
2.8. Refit mounting plate (5) to main post (1) and locate with
locking pin (6).
2.9. Attach the four mounting arms (Fig.3.7) to mounting plate (5)
with bolts (8), washers (9 & 11) and nuts (10).
2.10. Insert handle (26, NOT SHOWN) through hole in stem of
mounting plate (5).
 WARNING! Ensure all Health and Safety, local authority, and general workshop
practice regulations are strictly adhered to when using this equipment.

Before using the stand ensure it is in good working order.
 Replace or repair damaged parts. Use recommended parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
 Keep the stand clean for best and safest performance.
 Locate the stand in a suitable work area, keep area clean and tidy and
free from unrelated materials. Ensure there is adequate lighting.
 Use on a firm, level surface capable of sustaining the stand and the load.
 Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
 Ensure all non-essential persons keep a safe distance whilst the stand is in
use.
 Lock mounting plate in position with locking pin before fixing a load and ensure
the load is centred and securely mounted on the mounting plate.
 When an engine is mounted, take the weight of the engine on the handle
before removing the locking pin.
 Ensure the stand and load are stable.
 To move a loaded stand, steady the load and push from behind the main
post of the stand so that the castor wheels are ahead of the load.
 DO NOT pull the unit backwards, or push from the side, as this may cause
the stand to tip.
 Ensure surface over which the stand is to travel is strong enough to take
the stand and load and that it is not cracked, uneven or obstructed.
 DO NOT use unit if damaged.
 DO NOT allow untrained persons to use the stand.
 DO NOT exceed the rated capacity of 450kg.
 DANGER! DO NOT work under an engine mounted on the stand.
 DO NOT use the stand for purposes other than those for which it is designed.
 When not in use store stand in a safe, dry, childproof area.
2. ASSEMBLY
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND
WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SPECIFICATION:
Max capacity ........... 450kg
Width ..................... 790mm
Length.................... 950mm
Height .................... 930mm
[email protected]
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
We b
email
WHEEL HUB FACING
INWARDS
REAR WHEEL ASSY.
Fig.1
Fig.1
Fig.2
Fig.3