Sealey SCR15 User Manual
Gas sprung mechanic's seat, Scr15
Original Language Version
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this seat.
Locate seat in a suitable working area.
WARNING! Use the seat on level and solid ground, preferably concrete.
Keep the seat clean and tidy in accordance with good workshop practice.
DO NOT use the seat
for any purpose other than that for which it is designed.
DO NOT stand on the seat.
DO NOT use the seat outdoors.
DO NOT get the seat wet or use in damp or wet locations or areas where there is condensation.
DO NOT clean the seat with any solvents which may damage the paint surface or the protective coating on the padded seat.
DO NOT exceed maximum capacity of 136kg.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCR15
Max. Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . 136kg
Minimum Height: . . . . . . . . . . . . . . . . . . . . . . . . 380mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . 520mm
4 .1 .
If the 5 swivel castors, 5 domed head nuts and 5 plain washers are not fitted, invert the seat on to a non-scratch clean surface and fit
the five castors.
4 .2 . If the swivel castors are fitted, check the fixings for tightness and tighten if necessary.
INSTRUCTIONS FOR:
GAS SPRUNG MECHANIC'S SEAT
MODEL NO:
SCR15
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY . NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS . USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED . FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY . KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE .
Thank you for purchasing a Sealey product . Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance .
1 . SAFETY
2 . INTRODUCTION
3 . SPECIFICATION
4 . ASSEMBLY
6 . MAINTENANCE
6 .1 .
If in constant use, check the tightness of the domed head nuts on a quarterly basis.
6 .2 . Smear the castor bearings and the gas cylinder rod with a thin film of silicone grease annually.
6 .3 .
The castor wheels are maintenance free; ensure they are able to rotate and swivel freely.
6 .4 .
Clean the seat cushion and trays with a moist cloth and mild detergent.
SCR15 Issue: 1 - 08/09/14
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
© Jack Sealey Limited
5 . OPERATION
5 .1 .
To lower: sit lightly on the stool and lift the operating lever; the stool will lower until the lever is released.
5 .2 .
To raise: remove weight from seat. Lifting the operating lever will allow the seat to raise.
Swivel action seat with lever operated gas sprung height adjustment between 380mm and 500mm. Padded cushion for added comfort. Seat
glides across workshop floor on five Ø60mm ball bearing castors. Base doubles as temporary tool and component storage tray.