Sealey X137 User Manual
X137, Cross beam adaptor 3tonne 4 x 4, Instruction manual for
Refer to the Safety Precautions supplied with your jack.
Use jack in an adequate working area for its function, keep area clean & tidy and free from unrelated materials. Ensure there is adequate lighting.
Before use ensure the weight does not exceed the capacity of the jack.
Ensure that the cross beam adaptor is complete and all components are in good working order.
Keep all unauthorised persons away during lifting and lowering.
Maintain correct balance and footing, wear non slip steel toe capped shoes.
Remove ill fitting clothing, ties, watches, rings, loose jewellery, and contain and/or tie back long hair.
Ensure the vehicle handbrake is engaged and the transmission is in 1st gear or reverse.
Ensure a minimum distance of 500mm between vehicle and walls, doors etc..
Only place the cross beam adaptor under those lifting points recommended by the vehicle manufacturer.
DANGER! The cross beam adaptor is for lifting and lowering only. Axle stands MUST support vehicle during servicing.
DO NOT exceed the rated capacity of the adaptor or jack.
DO NOT allow untrained persons to operate the adaptor or jack.
DO NOT place any part of your body within or under the vehicle during lifting or lowering.
DO NOT work beneath vehicle until axle stands are correctly positioned.
DO NOT operate equipment when tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT use the cross beam adaptor for purposes other than that for which it is designed.
DO NOT make any modifications to the adaptor.
After use clean all parts and store in a safe and dry child proof location.
InStRUctIOn MAnUAL fOR:
MODEL nO:
X137
thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATIONS
MODEL X137
Rated capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3000kg
Minimum height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140mm
Maximum height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230mm
Screw adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90mm
3. ASSEMBLY & PARTS
Unpack the product and check contents. Should there be any
damaged or missing parts contact your supplier immediately.
3.1. Wind the knurled thumb nut (item 2) on to the threaded
yoke (item 1) with knurled shoulder uppermost as in
fig.1.
3.2. Look for the keyway slot in threaded yoke and align with
the tapped hole in end of load beam (item 3).
3.3. Screw the cap screw in toward the threaded yoke
keyway slot without clamping. this screw keeps the
yoke 'v' on the axis of the beam.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
cross Beam Adaptor which quickly and safely overcomes the awkward job of lifting 4 x 4 vehicles with offset differentials. Simply remove the
existing trolley jack saddle*, replace with cross beam adaptor, fit the jack saddle into the hole in the adaptor and you are ready to lift. Suitable
for jacks with a 31-33mm saddle spigot pin, including Model no's 3000cXD, 3000LQ, 3001LE, 3003cXQ, 3010cX, 3012cXD and 3030cXD.
*note: Remove any rubber jack pad from the saddle before using to improve safety.
Existing trolley jack saddle*
(remove rubber pad)
CROSS BEAM ADAPTOR 3tonne 4 x 4
2
Item Part number
Description
Qty
1
X137-03-01
threaded yoke (M30 X 3.5)
1
2
X137-03-02
thumb nut (M30 X 3.5)
1
3
X137-03-03
Load beam (70 X 50 X 430)
1
4
X137-03-04
M6 X 16 cap screw (yoke guide) 1
4. OPERATION AND MAINTENANCE
4
1
3
Ø30 Spigot jack adaption
4.1. Remove trolley jack saddle from jack and the rubber pad from the saddle.
4.2. Place the assembled beam as shown in fig.1 on to the jack spigot hole.
4.3. Position the assembly beneath the vehicle axle as fig.2. Keeping the
beam horizontal, jack the saddle up to the differential casing. Adjust yoke
height to engage with back axle housing for smooth lifting.
4.4. Raise vehicle to required height and immediately position axle stands to
support vehicle during servicing. (
See safety instructions)
4.5. Lower the vehicle by method 4.3. Remove axle stands and lower.
4.6. After use, clean with a lightly oiled cloth with attention to M30 thread.
fig.2
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
© Jack Sealey Limited 2013
fig.1
X137 Issue: 2(SP) -16/07/13