Sealey BB1502 - Manual (Page 2)

Model No:........................................................................BB1502
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Fuse rating: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5A
Axle Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13mm
no load Speed : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2850rpm
Wheel diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9kg
4.1. Installation
4.1.1. Bolt the polisher securely to a workbench using the base securing holes as a template. Check that all assembly nuts and bolts are
secure before powering. DO NOT block the 4 motor ventillation paths through the base.
4.2. Wheel fitting (fig.1)
4.2.1. Place the spacer over the axle shoulder.
4.2.2. "Sandwich" the selected buffing wheel between the clamp rings and secure with the hexagon nut, hand tight. (The axle threaded
ends are handed lH and RH)
4.2.3 Tighten the nuts enough to grip without crushing the buffing wheel. Wheel rotation, in use, will tighten the hexagon nut.
Designed for quick and easy smoothing/polishing of metal and other materials. Efficient 370W (Model BB1502) and 550W (Model BB2002)
motors provide sufficient power for most tasks, while the cast iron base reduces vibration. Supplied with fine and course buffing/polishing
wheels and fitted ASTA approved plug.
 DO NOT touch the workpiece immediately after polishing as it may be very hot.
 DO NOT hold unsecured work in your bare hands, and DO NOT touch the buffing wheel whilst operating, or whilst plugged into the
mains power.
 DO NOT leave the polisher running unattended.
 DO NOT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 When not in use, switch the polisher off and remove the plug from the power supply.
2. INTRODUCTION
3. SPECIFICATION
Model No:........................................................................BB2002
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Fuse rating: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13A
Axle Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mm
no load Speed : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2850rpm
Wheel diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10kg
4. ASSEMBLY
RH THREAD EnD
lH THREAD EnD
"I/o" on/off
Switch
M12 (Model
n
o BB1502)
M16 (Model
n
o BB2002)
Buffing wheel
Clamp ring
Spacer
Hex nut
RH/lH
Direction of rotation
fig.1
BB1502 BB2002 Issue: 1 - 06/01/15
Original Language Version © Jack Sealey limited
Motor vent (4 sides)