Sealey VS313 - Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
GLOW PLUG PULLER SET
MODEL No:
VS313
 WARNING! Ensure Health and Safety, local authority and general work
shop practice regulations are adhered to when using tools.

DO NOT use tool if damaged.
 Maintain tool in good and clean condition for best and safest performance.
 Wear approved eye protection. A full range of personal safety equipment is
available from your Sealey dealer.

Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie
back long hair.

DO NOT attempt to start engine or move vehicle, whilst tools are fitted and
work is in progress.

Ensure any disconnected fuel pipes are plugged to avoid spillage.
 Account for all tools and parts being used, DO NOT leave them in or near
the engine. Return all parts to the case and store this in a safe, dry,
childproof location.

IMPORTANT: These instructions are provided as a guide only. Always
refer to the vehicle manufacturer’s service instructions, or a proprietary
manual, to establish the current procedure and data.

WARNING! The warnings referred to in this guide cannot cover all
possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
A comprehensive kit suitable for removing stubborn glow plugs. Ideal for removing
plugs that have been unscrewed, but seized, due to residue build up or where the
filament has been distorted. Quick and effective method saving time and money.
2. INTRODUCTION
1. SAFETY INSTRUCTIONS
3. INSTRUCTIONS
Note! Ensure the glow plug has been fully unscrewed from the cylinder
head, if not damage to the threads in the cylinder head may occur.
3.1 Take the correct sized glow plug collet (fig.1.4) and insert it through the
appropriately sized sleeve (fig.1.1). Ensure the flange on the sleeve is the
same side as the thread on the collet.
Note! The glow plug may not take an external collect but has the internal
recess to accept the internal collet (fig.1.2).
3.2 Screw the collet into the tool (fig.1.3, screw back the pressure screw (fig.3)
to allow the collet to be screwed fully home.
3.3 Insert the collet over the end of the glow plug or inside the glow plug
(dependant on the type of collet needed).
3.4 Screw down the pressure screw so the collet tightens securely to the glow
plug.
3.5 Use the slide hammer (fig.3) to gradually remove the seized glow plug.
3.6 If the glow plug cannot be removed, it may be necessary to use a suitable
penetrating oil and leave for a period of time to assist the removal.
If the glow plug still cannot be removed, consult a main dealer or diesel
specialist, to avoid damage to the engine.
fig.1
fig.3
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version VS313 Issue: 2 - 01/06/12
fig.2