Sealey VS906 User Manual
Vs906, Fig.1, Mini digital thermometer
WARNING! Ensure Health & Safety, local authority, and
general workshop practice regulations are adhered to when
using this equipment.
Familiarise yourself with the application and limitations of the
product, as well as potential hazards peculiar to the use of the
thermometer.
Keep the thermometer clean for best and safest
performance.
Store the thermometer in its protective cover when not in use.
When not in use, store in a safe, dry, childproof area.
DO NOT use equipment for any purpose other than that for
which it is designed.
DO NOT allow untrained persons to operate the thermometer.
DO NOT use the thermometer to test objects above 250ºC.
High precision digital thermometer with the sensor located in the
tip of the stainless probe. Compact and lightweight measuring
both °C and °F with hold function. Ideal for testing automotive air
conditioning output. Powered by 1.5Volt cell (supplied).
Temperature Range: -40°C to +250°C (-40°F to +482°F)
Original Language Version
VS906 Issue: 1 - 26/11/10
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
3. DISPLAY
4. OPERATION
5. MAINTENANCE
INSTRUCTIONS FOR:
MINI DIGITAL THERMOMETER
MODEL No:
VS906
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
4.3 Switch between Centigrade and Fahrenheit by pressing
the º
C/ºF button.
4.4 Press the
HOLD button to hold the current reading on the
display (the 'HOLD' symbol will begin to flash). To see the
maximum reading of all the readings taken since switching
on press
HOLD again ('MAX' will flash on the display). To
see the minimum reading of all the readings taken since
switching on press
HOLD again ('MIN' will flash on the
display). To return to temperature measurement mode press
HOLD again. This cycle can be repeated at any time.
4.5 Turn the thermometer OFF by pressing the
ON/OFF button
again. NOTE: Current readings are not held in memory
when the thermometer is turned off.
4.6 If the thermometer is ON but not in use it will turn itself off
after approximately 20 mins.
4.7 If the measured temperature is over 250ºC the display will
show '
H - - '.
If the measured temperature is under -40ºC the display will
show '
L - - '.
4.1 Remove the protective cover from the probe. The cover can,
if required, be stowed on the other end of the thermometer
body.
4.2 Turn the thermometer ON by pressing the
ON/OFF button.
The display will show all its symbols momentarily (as shown
in fig.1) and then revert to zero. Once the tip of the probe
has sensed the temperature the display will change from
zero to that temperature.
5.1 After use, clean the probe with warm water and replace the
protective cover.
5.2 If the display appears fuzzy or faded the battery should be
replaced. (1.5V, LR44 or equivalent).
fig.1
Environmental Protection
When the product is no longer required, it must be
disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling
information.
Battery Removal
Remove the battery from the thermometer by rotating
the circular battery compartment cover on the back of
the casing. Lift off and tip out the battery.
Dispose of battery according to local authority
guidelines. WARNING: Do not dispose of by fire. This
could result in an explosion. Under the Waste Batteries
and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products
containing batteries (as defined within these regulations),
that they are registered with Valpak’s registered
compliance scheme. Jack Sealey Ltd’s Batteries
Producer Registration Number (BPRN) is BPRN00705.