Sealey PC300SD - Manual (Page 2)

PC300SD.V3 Issue No:2 19/10/09 Original Language Version
 WARNING! Ensure you read, understand and apply Section 1 ‘Safety Instructions’.
Reminder: DO NOT vacuum hazardous substances. Use of an incorrect cartridge filter will invalidate your warranty.
4.1 ensure the machine is unplugged from the power supply. (fig.3.1)
4.2 remove the top section and with the raised rim uppermost fit the
cartridge filter tube down over the filter basket and push fully home.
Place the locking disc onto the top of the filter and turn the locking bar
until the latch drops into the slot in the top of the filter cage. Continue
turning until the filter is fully locked down. (fig.3.2)
4.3 reposition the head onto the drum body, and clip in place. (fig.3.3)
4.4 Insert the larger end of the flexible hose into the front inlet on the
container and lock in place. Push the required attachment onto
the free end of the hose. (fig.3.4)
4.5 Plug in the power supply. (fig.3.5)
4.6 Switch to the ‘on’ (position ‘I’). (fig.3.6)
4.7 When you have completed vacuuming, press the switch to ‘off’
2. cONTeNTS AND SpecIFIcATIONS
2.1 carton content
2.1.1 Carefully unpack the carton.
2.1.2 locate the two side clasps (fig.1.6) which hold the top section
(fig.1.3) in place.
2.1.3 undo the clasps, remove the top section and take out the items
in the container.
2.1.4 Check and identify each component as listed below. If anything
is missing or damaged please contact your supplier immediately.
2.2 Specification
motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V / 1400W
max. Vacuum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160mbar
Air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120m³/h
Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30ltr
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.4kg
Vac Accessories Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35mm
filter (See Sect.9 ‘Consumables’) - Dry: . . . . locking Cartridge filter
filter (See Sect.9 ‘Consumables’) - Wet: . . . . . . . . . . . . . . . . . . .foam
4. DRY vAcUUm cLeANING
3. ASSemBLY
3.1 ensure the mains plug is disconnected. (fig.2.1)
3.2 undo clasps. (fig.2.2)
3.3 lift off the top section assembly. (fig.2.3)
3.4 remove contents from inside the container. (fig.2.4)
3.5a turn the container upside down and insert the castors ensuring they
are pushed all the way in. (fig.2.5a)
3.5b Insert the rear wheel shaft (N) into the rear support block. Insert washer
(m) on the shaft, then insert rear wheel (K) on the shaft. Insert the
lock pin (r) into the hole on the end of the shaft to lock the wheel. Snap
the hub cap (o) on to the wheel. repeat the same steps at the other
end of the shaft. (fig.2.5b)
3.6 for wet vacuum cleaning fit the supplied foam filter. (fig.2.7)
3.7 for dry vacuum cleaning use the locking cartridge filter supplied. (fig.2.6)
NOTe: Do not operate the cleaner without a cartridge filter fitted as
this will damage the machine and invalidate your warranty.
3.8 replace the top section onto the container. (fig.2.8)
3.9 Align up the top section with the clasps and snap into place, by applying
pressure at the mid point of the clasps. (fig.2.9)
3.10 Insert the large end of the hose into the front inlet of the container and
lock in place by turning clockwise a quarter turn. (fig.2.10)
3.11 Choose the desired nozzle and push it onto the telescopic suction tube.
5. WeT vAcUUm cLeANING
 WARNING! Ensure you read, understand and apply Section 1 ‘Safety Instructions’. Reminder: Remove plug from power supply
before opening unit. DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil, spirits, paint,
thinners, acids etc.
Item Description Item Description
1 Handle 11 telescopic suction tube
2 oN/off switch 12 Blow connection
3 top section 13 Combination nozzle
4 filter basket 14 air regulator handle
5 Safety float valve 15 foam filter
6 Clasp 16 Crevice nozzle
7 Container, (Stainless Steel) 17 locking Cartridge filter
8 Vacuum hose connection (fitted as standard)
9 Drain Plug 18 Noise Diffusion muffler
10 flexible vacuum hose
fig.1
fig.2
fig.3