Sealey MS900PSEU - Manual (Page 2)

3. TEChNICAL SpECIFICATIONS
 WARNING! DO NOT sand any materials containing asbestos.
 DO NOT switch the polisher/sander on whilst the head is in contact with the work piece and avoid unintentional starting.
 DO NOT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.
 DO NOT allow untrained persons to operate the polisher/sander.
 DO NOT operate the polisher/sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 DO NOT use the polisher/sander where there are flammable liquids, solids or gases such as paint solvents, etc.
 DO NOT leave the polisher/sander operating unattended.
 DO NOT carry the polisher/sander with your finger on the power switch.
 DO NOT pull the cord to remove the plug from the power supply.
 Use a qualified person to lubricate and maintain the polisher/sander.
 When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODuCTION
1300W professional polisher/Sander. Features six speed power control producing speeds suitable for polishing and sanding. Speeds vary
from 1000rpm to 3000rpm. Alloy bevel gear head with composite motor housing. Supplied with 170mm diameter backing pad, disc spanner
and side handle. Fitted with Schuko plug.
4. CONTENT & ASSEMBLY
4.1. Content
4.1.1. Check the contents of the carton. If any item is missing or damaged contact
your supplier immediately.
Fig1.1: polisher unit, 2: Side handle, 3: pad, 4: Spanner.
4.2. Assembly
 WARNING! Ensure unit is not plugged into mains before attempting any assembly.
4.2.1. Attach the side handle (fig.1.2). Note: there is a mounting hole on either side and the top to suit the application and/or operator.
4.2.2. To attach the rubber pad:
Thread the rubber pad (fig.2.3) on shaft (S) and tighten using spanner (fig.1.4) by holding shaft steady with locking button (fig.4).
4.2.3. To fit a sanding disc: Select the grade of self adhesive sanding disc required (D), peel off the backing and centrally locate the disc
onto the rubber pad.
4.2.4. To fit a polishing bonnet:
Fit the polishing bonnet (Z) over the secured rubber pad, using the pull cord, tighten the bonnet and tie a bow to secure, tuck the
loose ends of the bow neatly under the bonnet.
Fig.2 Fig.3
LEAD PAINT WARNING! Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is
toxic and must therefore be avoided. The following action must be taken before using machine as a sander:
1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead
paint dust: Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
A) Paint Spray Respirator (Sealey ref. SSP1699) B) PE Coated Hooded Coverall (Sealey ref. SSP266). C) Latex Gloves (Sealey
ref. SSP24).
4. Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly clean
all areas when task is complete.
5. Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
Fig.4
1
2
3
4
LOCKING
BuTTON
Model . . . . . . . . . . . . . . . . . . . . . . MS900pSEu
Nominal Power Rating . . . . . . . . . . . .1300Watts
Power Input . . . . . . . . . . . . . . . 5.8Amps @ 230V
No Load Speed . . . . . . . . . . . . . 1000 - 3000rpm
Noise Power . . . . . . . . . . . . . . . . . . .102.04dB.A
Noise Pressure . . . . . . . . . . . . . . . . . .91.04dB.A
Vibration (Load). . . . . . . . . . . . . . . . . . 3.402m/s²
Uncertainty Value(k) . . . . . . . . . . . . . . . . 1.5m/s²
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.8kg
Supply . . . . . . . . . . . . . . . . . . . . . . . . .230V-5.8A
Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . 170mm
Thread Size. . . . . . . . . . . . . . . . . . . .M14 x 2mm
Original Language Version MS900PSEU Issue: 1 - 16/01/13
Fig.1
© Jack Sealey Ltd