Fig.3 fig.4 fig.5, General instructions – Sealey ML300/110 User Manual
Page 2
3. general inStrUctiOnS
Warning! ensure the light is disconnected from the mains power supply before attempting any of the following.
3.1. aSSeMblY
3.1.1. Slide the high end of the stand into the black clamp as indicated in fig.3. Align the threaded insert in the stand with the hole in the black clamp and screw
in the fixing knob ensuring that the contoured washer on the threaded part fits the curvature of the clamp. Adjust the angle of the floodlight as required and
tighten the knob to grip the stand.
3.2. general
Use only original Sealey parts for repair or replacement. Repairs must only be undertaken by a qualified electrician.
Clean the light with a dry, dust-free cloth.
DO nOt use solvents or abrasives to clean the light.
Avoid touching the glass shield (fig.5.2) as handling may reduce service life and cause the glass to crack. If necessary clean the shield (when cold) with
alcohol and a soft cloth. If the glass is damaged, replace it immediately. Use genuine Sealey replacement glass.
DO nOt use other glass and DO nOt
use the light without the glass shield.
Although weather proof, the light must not be stored wet. Should the unit become wet, unplug from mains and wipe dry before storing.
DO nOt use the light without the weather seal intact.
3.3. bUlb cHanging
Warning! Disconnect the light from the power supply and allow to cool before attempting to touch the unit.
DO nOt touch the new halogen bulb as the natural oil from your fingers will shorten the bulb life. Handle with a dry, clean cloth only.
3.3.1. Loosen the screw on the top of the front cover (fig.5) and undo, allowing the front cover to open. Check to ensure that the screw is retained in the front
cover tab (3) by the washer.
3.3.2. Remove the old bulb and discard. Hold the new bulb (1) in a clean cloth and insert it (always use the correctly rated bulb).
3.3.3. Check that the weather seal is correctly located in the rim (4) and the washer is on the securing screw. Close the font cover. Seal by tightening the
securing screw.
If you use an extension lead the cable must be fully unwound from the drum.
The light is weather proof and may be used out doors. Ensure any extensions and plugs are weatherproof.
Danger! DO nOt direct the light into a person’s eyes. all models have a very intense light output which, if incorrectly used, could cause eye
damage.
DO nOt touch the light when operating. Allow to cool before touching, light operates at high temperature.
DO nOt handle halogen bulbs as the natural oil from your fingers will shorten the bulb life. Handle only with a soft dry cloth.
DO nOt use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack.
DO nOt use the light without the weather seals intact.
DO nOt use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a safe, dry, childproof area.
nOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPOrtant: no liability is accepted for incorrect use of this product.
WarrantY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inFOrMatiOn: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
ML300/110.V2 Issue: 1 - 17/05/11
fig.3
fig.4
fig.5
environmental Protection.
Recycle unwanted materials instead of
disposing of them as waste. All tools,
accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a
manner which is compatible with the
environment.
When the product is no longer required, it
must be disposed of in an environmentally
protective way. Contact your local solid waste
authority for recycling information.