Sealey ADB06 User Manual
Adb06, Instructions for, Model no
WARNING! Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to this product.
Maintain the pump station in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the warranty.
Use only to dispense water and urea solutions.
Ensure safety eye protection and protective clothing are worn when using this product.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
After use, drain any fluids from the equipment before storage.
Dispose of waste liquids in accordance with local authority regulations.
DO NOT exceed the maximum pressure of 50psi.
DO NOT point the nozzle at people or animals.
DO NOT use the equipment near open flames.
DO NOT smoke whilst using this equipment.
DO NOT use to extract corrosive fluids.
DO NOT dismantle, tamper with or adapt the equipment for any purpose other than for which it is designed.
DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
Keep the pump clean and store in a safe dry, childproof location.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment. All liquids must be disposed of according to
local authority regulations.
InstRUctIons FoR:
PROFESSIONAL ADbLuE®
AuTOMATIC DELIVERY NOZZLE
WITH METER
MoDEl no:
ADb06
1. SAFETY INSTRuCTIONS
2. INTRODuCTION
3. INSTALLATION
IMPORTANT: PLEASE READ THESE INSTRuCTIONS CAREFuLLY. NOTE THE SAFE OPERATIONAL REQuIREMENTS,
WARNINGS AND CAuTIONS. uSE THIS PRODuCT CORRECTLY AND WITH CARE FOR THE PuRPOSE FOR WHICH IT IS
INTENDED. FAILuRE TO DO SO MAY CAuSE DAMAGE OR PERSONAL INJuRY AND WILL INVALIDATE THE WARRANTY.
PLEASE RETAIN THESE INSTRuCTIONS FOR FuTuRE uSE.
thank you for purchasing a sealey product. Manufactured to a high standard this product will give you years of trouble free performance
if these instructions are carefully followed and the product is correctly maintained.
ADB06
Issue no: 1 - 19/06/13
lightweight yet durable nozzle developed to meet the International standards of urea dispensing. this AdBlue® nozzle has an incorporated
ADB02 digital flow meter, which allows the user to view the delivery readings at the vehicle. Manufactured using AdBlue® compliant materials
and fitted with 3/4"BSP hose inlet. Features a maximum flow rate of 35ltr/min.
4. NOZZLE OPERATION
Ensure the pump is turned off.
3.1 Apply a sealant (e.g: PTFE tape) thinly to hose thread
3.2 screw the hose into the new nozzle and tighten by using
a wrench on the hose nut only, (do not overtighten).
3.3 the nozzle is now ready for use.
4.1 Place the nozzle fully into the receiving tank.
4.2 Squeeze trigger (fig.1) to dispense fluid.
4.3 The trigger may be locked in the open position by squeezing and pushing the trigger lock back. (fig.2). This feature can be disabled if
necessary by removing the 'U' shaped staple from the handle. (Drift the staple out with a small pin-punch).
4.4 When the level of the fluid reaches the tip of the nozzle the flow will close off automatically.
4.5 When not in use, place the nozzle in a leak proof housing.
fig.1
fig.2
Original Language Version
© Jack sealey limited
ADb06
Measurement system
Turbine (Polypropylene)
Flow Rate
35 ltr/min
operating pressure (Max) 50psi
storage temperature
(Range)
-20°c to 70°c
storage humidity (Max)
95%
operating temperature
(Range)
-10°c to 50°c
Viscosity (Range)
2 to 5.35 cst
Accuracy
(between 15 and 120l/min)
+/-1% of value indicated
after calibration
Reproducibility (typical)
+/- 0.3%
Power supply
2 x 1.5V AAA alkaline batteries (included)
Battery life
18 to 36 months
compatible Fluids
Water, Urea
Inlet connection:
¾" BSP