Sealey TP6807 User Manual
Safety instructions 2. introduction, Rotary oil pump heavy-duty high flow, Tp6807
Please take time to read the following safety information before commencing work with this pump.
WARNING! Ensure health & safety, local authority, and general workshop practice regulations are
strictly adhered to when using this equipment.
Familiarise yourself with the applications, limitations and potential hazards of this product.
Maintain the pump in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Non authorised parts will invalidate the
warranty.
Use only with oils, diesel, anti-freeze and other non-corrosive fluids.
Ensure safety eye protection and protective clothing are worn when using this product.
Keep the work area clean, uncluttered and ensure that there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Dispose of waste liquids in accordance with local authority regulations.
Keep a foam or dry powder fire extinguisher nearby.
Ensure that containers cannot easily be knocked over during filling.
Remove all combustible materials from the work area.
HSE guidance recommends use of metal containers with secure caps for holding drained fuel.
Mark fuel containers with hazard labels to identify the contents.
Keep any fuel containers in a well ventilated, lockable store, preferably away from the working area.
Soak up any spill immediately using absorbent granules or similar material.
DO NOT use to extract corrosive fluids.
DO NOT dismantle, tamper with or adapt the pump for any purpose other than for which it is designed.
DO NOT use the pump if it has been dropped or mishandled, check the pump to ensure that it is not damaged.
DO NOT use the pump as a handle to move the fluid container.
WARNING! DO NOT allow uncontrolled discharge of fluids, thus polluting the environment.
DO NOT use an open flame or smoke anywhere near the pump or around stored fuel.
DO NOT use the pump to transfer hazardous or harmful chemicals, corrosive liquids, solvents,
alkalies or acids.
DO NOT use the pump with water.
DO NOT allow work which can produce a source of ignition, such as welding, electrical or other hot
work, to be carried out whilst dispensing fuel.
DO NOT use cordless or mobile phones, ensure these items are turned off before dispensing fuel.
DO NOT use the pump for any purpose other than for which it is designed.
DO NOT use whilst under the infuence of drugs, alcohol or other intoxicating medication, or if you
are fatigued.
Keep the pump clean and well oiled and store in a safe, dry, childproof location when not in use.
Users/Businesses should perform their own hazard risk assessment based on
their specific environment and following the guidelines laid out above.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION
InStRUctIonS FoR:
ROTARY OIL pUmp
HEAVY-DUTY HIGH FLOW
MoDEl no:
Tp6807
IMPORTANT: pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREmENTS, WARNINGS AND CAUTIONS.
USE THIS pRODUCT CORRECTLY AND WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO mAY CAUSE DAmAGE
OR pERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. pLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance
if these instructions are carefully followed and the product is correctly maintained.
Heavy-duty pump suitable for use with low viscosity products such as oils, diesel, anti-freeze and other
non-corrosive fluids. Supplied with 2"BSP adaptor and 3 piece dip tube, suitable for use on 205ltr drums.
Delivery approximately 1ltr per revolution, emptying 205ltr drum in 3 minutes.
Original Language Version
tP6807 Issue no:1 - 04/03/11