Sealey REG/MM - Manual (Page 2)

3. CONNECTION
4. OPERATION
5. STORAGE/MAINTENANCE
The function of the regulator is to reduce and control the pressure of a
gas. The regulator reduces the pressure at which the gas is stored, to
the pressure needed to use the gas. The regulator has been designed so
as to be used only and exclusively with the type of gas and at the
pressure which is shown by the markings stamped on the regulator body
(refer to the markings key earlier in section 2).
 WARNING! To try and use the regulator with types of gasses and
pressures other than those indicated can be dangerous and will
invalidate your warranty.
3.1 Mini Refillable/Disposable Cylinder. (REG/MM & REG/ MMG)
3.1.1 Check that the regulator is correct both for the type of gas and
the pressure in the cylinder to be used.
3.1.2 Turn the pressure adjusting knob clockwise to ensure that the
regulator valve is closed.
3.1.3 Replace the inlet connection seal if it is damaged or lost.
3.1.4 Screw the regulator to the cylinder valve and tighten.
DO NOT over-tighten.
3.2 Hose connection.
3.2.1 Attach hose to the outlet connection of the regulator by pushing
it in as far as it will go.
 WARNING! Only use hoses complying with EN 559-ISO3821.
3.3 Connection to Industrial Gas Cylinder. (REG/MZ only)
3.3.1 Before screwing on the regulator, briefly open the cylinder
valve, then close it, in order to remove any impurity (only for
rechargeable bottles).
 WARNING! During this operation it is dangerous to stand, or
place any parts of your body in front of the cylinder valve.
3.3.2. When using Argon or Argon mixtures, you will need to use the
“bull nose adaptor”. Fit the bull nose adaptor to the cylinder
with a spanner. (If you intend to use CO² gas the regulator will
fit directly onto the cylinder).
3.3.3 Screw the regulator to the bull nose adaptor or directly to the
cylinder valve as required and tighten using a suitable spanner.
DO NOT over-tighten.
3.4 Hose connection.
3.4.1 Push the gas supply tube onto the gas outlet nozzle on the
regulator and retain it with a suitable clip/clamp.
 WARNING! Only use hoses complying with EN 559-ISO3821.
4.1 Operation with Mini Refillable/Disposable Cylinder. (REG/MM
& REG/MMG.)
4.1.1 To increase pressure and flow slowly turn the regulator
pressure adjusting knob anticlockwise.
4.1.2 To decrease pressure and flow slowly turn the regulator
pressure adjusting knob clockwise.
4.1.3 Using the pressure adjusting knob it is possible to
compensate for eventual pressure drop within the cylinder.
 CAUTION! Outlet pressure must not be regulated higher than
the pressure you need to use.
4.2 Closing
4.2.1 Turn the pressure adjusting knob clockwise until it is
completely closed.
4.2.2 Release the gas until the regulator gauges (if fitted) indicate
"zero".
4.2.3 Remove regulator from cylinder.
5.1 STORAGE.
5.1.1 The regulator must be treated as a precision instrument.
5.1.2 When the regulator is not to be used for long periods, store it
in its wrapping or in its box, to prevent contact with dust, oil
and other sources of dirt.
5.2 MAINTENANCE.
5.2.1 Do not carry out maintenance or repairs, other than the
following:
Replacement of inlet seal.
Replacement of gauge (if fitted).
5.2.2 Use only original spare parts and accessories.
5.2.3 Do not clean gauge glasses with petrol, solvents or any other
kind of detergent.
5.2.4 In case of failure take your regulator back to the supplier.
5.3 Malfunctioning.
5.3.1 In case of malfunction (e.g. leaks in the gauges or in the relief
valves) stop use and unscrew the regulator immediately from
the bottle.
5.3.2 We suggest that the regulator be returned to the supplier to be
checked and repaired.

CAUTION! Do not use the regulator if there are the following
malfunctions:

The inlet seal is damaged or lost.
 The regulator or any of its parts (gauge, inlet connection, outlet
connection) are damaged or dirty, oily etc.
 There are any leaky connections.
 The relief valve adjustment has been modified or the valve
leaks.
5.4 Relief valve.
5.4.1 REG/MZ is equipped with an excess pressure valve.
5.4.2 In case of malfunctioning, this valve allows the excess gas
pressure to escape.

CAUTION! Do not modify the calibration of the relief valve.
5.5 Checking the seal
5.5.1 This check must be carried out only in the open air: use either
soapy water or a gas leak detector. Do not use flames.
5.5.2 Spray detector on the area to be checked.
5.5.3 The forming of bubbles or foam is a sign of a leak. If a leak is
detected remove regulator from service immediately and have
it serviced by an authorised dealer.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
4.3 Operation with Industrial Gas Cylinder. (REG/MZ only)
 CAUTION! Before opening the cylinder valve, ensure that the
regulator is completely closed (turn the pressure adjusting knob
anticlockwise).
4.3.1 Slowly open the cylinder valve.
4.3.2 To increase pressure and flow: slowly turn the regulator
pressure adjusting knob clockwise.
4.3.3 To decrease pressure and flow: slowly turn the regulator
pressure adjusting knob anticlockwise.
4.3.4 Using the pressure adjusting knob it is possible to
compensate for eventual pressure drop within the cylinder.
4.4 Closing
4.4.1 Close the cylinder valve.
4.4.2 Release any gas remaining in the supply hose.
4.4.3 Turn the pressure adjusting knob (5) anticlockwise until it is
completely closed.
4.4.4 Remove regulator from cylinder.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.
REG/MM.V2, REG/MMG.V2, REG/MZ.V2 Issue No.2(C) 22/01/14 Original Language Version © Jack Sealey Limited