Sealey LC800ST User Manual
Folding log rack, Lc800st, Fig.1
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SpECIFICATION
Maintain the log rack in good condition. Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
Keep the log rack clean.
Locate the log rack in a suitable working area. Keep area clean and tidy and ensure there is adequate lighting.
Ensure the log is correctly held and balanced before commencing work.
Maintain correct balance and footing. Ensure the floor/ground is not slippery and wear non-slip shoes and appropriate protective clothing
for the tool you are using.
DO NOT use the log rack for any purpose other than that for which it is designed.
DO NOT operate the log rack if any parts are missing as this may cause failure and/or personal injury.
DO NOT use the log rack if you are tired or under the influence of drugs, alcohol or medication.
4. ASSEMBLY
3. CONTENTS
(Refer to fig.1.)
4.1
Unpack the product and check contents to ensure no parts are damaged. Should there be any damaged or missing parts contact your
supplier immediately.
4.1.1
First screw the feet together. To do so arrange the feet (9) in pairs, screw each pair together with a M8x16 screw (10), 8mm washer
(8) and M8 lock nuts (7), so that the feet can still be folded.
4.1.2 Then insert the M6x12 screws (4) through the two slots in each pair of legs and secure with 6mm washers (3) and M6 lock
nuts (6). Check that the feet can still be folded.
4.1.3 Join together the pre-assembled feet with the cross struts (2) and the longer diagonal struts (5) using M6x12 cross head screws (12)
and longer M6x35 screws (11) to go through the feet, cross strut and the diagonal strut (5). Secure with M6 nuts (1).
Folding log rack with innovative serrated edges to safely hold single log firmly in place whilst cutting. Crossed bars for increased stability.
Easily folded flat for storage. Strong and sturdy so light enough to be easily moved, made of corrosion resistant metal.
pART DESCRIpTION
QTY
1) M6 nut
10
2) Cross strut
2
3) Ø6mm washer
6
4) Screw M6x12
3
5) Diagonal struts
2
6) Locknut M6
3
7) Locknut M8
3
8) Ø8mm washer
6
9) Feet (serrated tops)
6
10) Screw M8x16
3
11) Screw M6x35
2
12) Crosshead screw M6x12
8
inSTRUCTionS FoR:
FOLDINg LOg RACK
MoDEL no:
LC800ST
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: pLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OpERATIONAL REQUIREMENTS, WARNINgS, AND
CAUTIONS. USE THIS pRODUCT CORRECTLY, AND WITH CARE FOR THE pURpOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAgE AND/OR pERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Original Language Version
WARNINg! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. it must
be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.
Model No: . . . . . . . . . . . . . . . . LC800ST
Unfolded Size: . . . . . . . . . . . . 820x860x780mm
Folded Size: . . . . . . . . . . . . . . 820x70x1000mm
Maximum Log Ø: . . . . . . . . . . 250mm
Load Capacity: . . . . . . . . . . . . 150kg
fig.1
© Jack Sealey Limited