Sealey AK466D - Manual

1.1. ELECTRICAL SAFETY. p p
p
WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are
plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested by
a qualified Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage,
especially power connections, to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require
a fuse smaller than 13Amps for certain products (subject to 1.1.10. below) see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by
a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut off
and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked with
this symbol . To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue to the earth terminal.
1.1.10. Cable extension reels. When a cable extension real is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important. We recommend that at least 1.5mm 2 section cable but to be absolutely sure that the capacity of the cable reel is
suitable for this product and for others that may be used in the other output sockets, we recommend the use of 2.5mm 2 section cable.
INSTRUCTIONS FOR:
ELECTRIC OIL DRAINER
Model No:
AK466D
The use of symbols in this document is to attract your attention to possible danger. The symbols and warnings themselves do not eliminate any danger, nor are they substitutes for proper
accident prevention measures.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
Model - supplier code - Date
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
BBlluuee
N Neeuuttrraall
w wiirree
YYeellllooww && GGrreeeenn
EEaarrtthh wwiirree
w wiirree
rreessttrraaiinntt
FUSE RATING
THIS PRODUCT MUST BE FITTED
WITH A:
13 Amp FUSE
BBrroowwnn
LLiivvee
w wiirree
1.2 GENERAL SAFETY
p WARNING! Disconnect the pump from the mains power before changing accessories, servicing or performing any maintenance.
3 Keep the pump clean and maintain it in good condition (use an authorised service agent).
3 Replace or repair damaged parts. Use genuine parts only. Non authorised parts may be dangerous and will invalidate the warranty.
3 Locate pump in adequate working area for its function, keep area clean & tidy and free from unrelated materials. Ensure there is adequate lighting.
3 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
3 Sump oil temperature should be 50°C or above for extraction. Ensure you wear appropriate protective clothing and gloves.
3 Keep all non essential persons away from the working area.
3 Check pump connections and fitting before use. When the pump is turned on check that there are no leaks.
3 Ensure the collection tank reservoir capacity exceeds waste oil amount to be collected.
3 Avoid unintentional starting of the pump and ensure end nozzle is correctly inserted into the dip stick access hole before operating.
7 DO NOT use the pump for any purpose other than for which it is designed.
7 DO NOT use to extract diesel, petrol or flammable liquids.
7 DO NOT operate the pump if any parts are damaged or missing as this may cause failure or possible personal injury.
7 DO NOT pull or yank any pipes or hose, and do not attempt to move the pump by pulling the hose or cable.
7 DO NOT leave the pump operating whilst unattended.
7 DO NOT direct the nozzle at yourself or others.
8 DO NOT pull the cord from the power supply.
p WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
3 Dispose of waste oil in accordance with local authority regulations.
3 When not in use unplug from the mains power supply and store in a safe, dry, child proof area
AK466D - 3 - 290102